西门子6ES75121CK000AB0型号及参数 西门子6ES75121CK000AB0型号及参数 

6ES7512-1DK01-0AB0 SIMATIC DP,CPU 1512SP-1 PN 用于 ET 200SP, *处理器 mit 工作存储器 200 KB 用于 程序 和 1MByte 用于数据, 1. 接口:PROFINET IRT mit 3 Port 换机, 48 NS Bit-Performance, SIMATIC Memory 卡 必要, 总线适配器 必要 用于 Port 1 和 2

公司名称：上海朔川电气设备有限公司

• 联 系 人：吉梦琪
• ：
• 地址：上海市金山区泾波路129号
• ：2840735331

• CPU 1512SP-1 PN 订货数据   附件   产品信息   组态工具 跳转到 概述 应用 设计 功能 技术规范 概述 CPU 1512SP-1 PN 适用于基于 S7-1500 CPU 1513-1 PN 的 SIMATIC ET 200SP 适用于对程序范围和处理速度具有中等要求的应用，通过 PROFINET IO 和 PROFIBUS DP 进行分布式配置。 增强了系统和设备的可用性 可连接zui多 128 个 IO 设备的 PROFINET IO 控制器 PROFINET I-Device，用于连接作为智能 PROFINET 设备、带 SIMATIC 或第三方 PROFINET I/O 控制器的 CPU 适用于 4 个控制器的 PROFINET 共享智能设备 PROFINET IO IRT 接口，带集成 3 端换机 经由 PROFINET 的等时同步模式 具有多种通信功能： 编程器/OP 通信，PROFINET IO，开放式 IE 通信（TCP，ISO-on-TCP 和 UDP），Web 服务器和 S7 通信 （带可装载的 FB） OPC UA Server (Data Access) 作为运行系统选件，用于方便地将 SIMATIC ET 200SP 连接到第三方设备/系统 可选 PROFIBUS DP 主站，用于 125 个 PROFIBUS DP 从站（带 CM DP 模块 6ES7545-5DA00-0AB0） 可选 PROFIBUS DP 从站（带 CM DP 模块 6ES7545-5DA00-0AB0） 组态控制（选项处理） 集成运动控制功能，用于控制速度控制轴和定位轴，支持外部编码器，凸轮/凸轮轨道和探头 注 CPU 的运行需要使用 SIMATIC 存储卡。 总线适配器不在供货范围内，需要单独订购。 应用 CPU 1512SP-1 PN 适用于独立生产技术领域中对处理性能和响应速度具有中等要求的应用。CPU 1512SP-1 PN 可被用作 PROFINET IO 控制器或分布智能系统（PROFINET 智能设备）。集成式 PROFINET IO IRT 接口的设计形式为 3 端换机，这样就可以在系统中通过端口 1 和 2 建立总线型拓扑，并且也可通过端口 3 来连接编程设备/PC 或 HMI 设备。 作为智能设备使用时，CPU 1512SP-1 PN 可实现在本地对过程数据进行分布式预处理，并且仅将实际需要的信息传输到上位控制器。这样做有以下优势： 减轻*控制器的工作负荷 缩短对现场重要信号的响应时间 数据量减少，总线系统上的负荷降低 各单元经过预测试并进行平行调试，设置更快速 由于自带机械装置,增加了可用性和灵活性 组态清晰明了 CPU 1512SP-1 PN *独立于*控制器运行。如果其发生故障，CPU 1512SP-1 PN 仍继续运行。 位模块化设计的 ET 200SP I/O 系统和 CPU 1512SP-1 PN 可实现面向功能的站设计。 另外，CPU 通过易组态的块提供全面控制功能，以及通过标准化 PLC-open 块 提供连接至驱动器的能力。 设计 CPU 1512SP-1 PN CPU 可直接卡装到标准安装导轨上。它具有： A powerful processor: The CPU achieves command execution times as low as 48 ns per binary instruction. 大容量工作存储器： 200 KB 用于程序，1 MB 用于数据 SIMATIC 存储卡作为装载存储器； 允许附加固件更新、数据日志和归档等功能 位模块化扩展性，灵活性好； 任意组合达 64 个 I/O 模块（I/O 模块、工艺模块和通信模块）。zui大 1 m 的站宽度。 采用 ET 200AL 的混合配置；  通过“BU-Send”基本单元和“BA-Send”总线适配器，可以在可扩展的 I/O 系统 ET 200SP (IP20) 装置中集成进 ET 200AL (IP65/IP67) I/O 系统的zui多 16 个 I/O 模块。 PROFINET IO IRT 接口，带集成 3 端换机： 端口 1 和 2 通过总线适配器来连接 （CPU 1512SP-1 PN 未提供总线适配器，不使用该适配器也可运行）。 如果需要，可以单独订购适当的总线适配器（BA 2xRJ45、BA 2xFC、BA 2xSCRJ、BA SCRJ/RJ45、BA SCRJ/FC、BA 2xLC、BA LC/RJ45 或 BA LC/FC）。 端口 3 集成式 RJ45 接口 集成通信功能： 编程器/OP 通信 PROFINET IO 开放式 IE 通讯（TCP，ISO-on-TCP 和 UDP） OPC UA 服务器 (数据存取) Web 服务器 S7 通信 S7 路由 数据集路由 免维护数据备份（无电池） 用于错误 (Error)、运行状况 (RUN/Stop)、维护 (MT)、电源 (PWR) 以及每个端口一个链路 LED 的诊断显示 可选标签采用浅灰色或黄色标签条。有两种材料可供选择： 标签箔和带有 500 个标签条的标签卷，用于热转印打印机 标签纸 (280 g/m2)，规格 DIN A4，每张 100 个标签条，适用于激光打印机 ET 200SP CPU 可带有一个参考 ID 标签 借助于总线适配器，可实现不同的 PROFINET 连接类型 在具有中等机械及 EMC 负荷的标准应用中，可以使用带 RJ45 接口的 SIMATIC 总线适配器，如总线适配器 BA 2xRJ45。 对于设备上承受较高机械和/或 EMC 负荷的机械设备和系统，建议使用可连接 FastConnect (FC) 电缆或光缆（SCRJ 或 LC）的 SIMATIC 总线适配器。同样，带有光纤电缆接口（SCRJ、LC）的所有 SIMATIC 总线适配器可用于更高的负载。 带有光纤电缆连接用总线适配器可用于覆盖两个站和/或较高 EMC 负载之间的较高电位差。 在将 AC I/O 模块或 AI Energy Meter ST 用作*个 I/O 模块时，应将深色的基本单元用作 ET 200SP CPU 后面的*个基本单元 供货清单： CPU 1512SP-1 PN（包括服务器模块）、24 V DC 连接器和总线适配器端口盖（总线适配器须单独订购） 功能 高效性 高速命令处理 功能强大的网络接口： 每个 CPU 均配备 PROFINET IO IRT (3 端机) 作为标准接口。 集成技术 通过标准化的块 (PLCopen) 连接模拟驱动器和具有 PROFIdrive 功能的驱动器 支持转速控制轴和定位轴以及外部编码器 精确位置传动可实现轴之间的同步操作 具有所有 CPU 变量的跟踪功能，用于实时诊断和偶发故障检测 全面的控制功能，例如，通过便于组态的块可自动优化控制参数实现*控制质量 等时同步模式 通过恒定总线循环时间，将分布式信号采集、信号传输和程序执行与 PROFIBUS 循环进行同步 集成安全功能 通过密码进行知识保护，防止未经许可证读取和修改程序块 通过复制保护，可绑定 SIMATIC 存储卡的程序块和序列号：只有在将配置的存储卡插到 CPU 中时，该程序块才可运行。 4-级 *理念：与 HMI 设备的通信也会受到限制。 操作保护：控制器识别已改变的或未经*的工程组态数据的传输 集成式系统诊断 TIA Portal 中、HMI 设备上以及 Web 服务器上以普通文本形式*显示系统诊断信息（甚至能显示来自变频器的消息），即使 CPU 处于停止模式也会进行更新。 集成在 CPU 的固件中，无须进行特殊组态。 通过集中设置进行组态控制（选项处理） 控制器中可存储各种硬件配置： 在用户程序中修改配置（启动 OB100） 配置结束时改装选件 可使用占位模块。 SIMATIC 存储卡(用来运行 CPU) 用作插入式装载存储器，或用于更新固件。 还可用于存储附加文档或 csv 文件（用于配方和归档） 通过用户程序的系统函数创建数据块实现数据存储/读取 数据记录（归档）和配方 配方和归档以 csv 文件保存在 SIMATIC 存储卡中； 便于使用 Office 工具或通过 web 服务器，访问工厂运行数据 通过 Web 浏览器或 SD 读卡器，可方便地访问机器的组态数据（与控制器之间的双向数据换） 编程 使用 STEP 7 Professional V13 update 3 或更高版本进行编程 技术规范 Article number 6ES7512-1DK01-0AB0   CPU 1512SP-1 PN, 200KB PROG./1MB DATA General information   Product type designation CPU 1512SP-1 PN HW functional status FS03 Firmware version V2.1 Product function   ● I&M data Yes; I&M0 to I&M3 Engineering with   ● STEP 7 TIA Portal configurable/integrated as of version V14 SP1 (FW V2.1) / V13 SP1 Update 4 (FW V1.8) or higher Configuration control   via dataset Yes Control elements   Mode selector switch 1 Supply voltage   Type of supply voltage 24 V DC permissible range, lower limit (DC) 19.2 V permissible range, upper limit (DC) 28.8 V Reverse polarity protection Yes Mains buffering   ● Mains/voltage failure stored energy time 5 ms Input current   Current consumption (rated value) 0.6 A Inrush current, max. 4.7 A; Rated value I²t 0.14 A²·s Power   Infeed power to the backplane bus 8.75 W Power loss   Power loss, typ. 5.6 W Memory   Number of slots for SIMATIC memory card 1 SIMATIC memory card required Yes Work memory   ● integrated (for program) 200 kbyte ● integrated (for data) 1 Mbyte Load memory   ● Plug-in (SIMATIC Memory Card), max. 32 Gbyte Backup   ● maintenance-free Yes CPU processing times   for bit operations, typ. 48 ns for word operations, typ. 58 ns for fixed point arithmetic, typ. 77 ns for floating point arithmetic, typ. 307 ns CPU-blocks   Number of elements (total) 2 000; Blocks (OB, FB, FC, DB) and UDTs DB   ● Number range 1 ... 60 999; subdivided into: number range that can be used by the user: 1 ... 59 999, and number range of DBs created via SFC 86: 60 000 ... 60 999 ● Size, max. 1 Mbyte; For DBs with absolute addressing, the max. size is 64 KB FB   ● Number range 0 ... 65 535 ● Size, max. 200 kbyte FC   ● Number range 0 ... 65 535 ● Size, max. 200 kbyte OB   ● Size, max. 200 kbyte ● Number of free cycle OBs 100 ● Number of time alarm OBs 20 ● Number of delay alarm OBs 20 ● Number of cyclic interrupt OBs 20 ● Number of process alarm OBs 50 ● Number of DPV1 alarm OBs 3 ● Number of isochronous mode OBs 1 ● Number of technology synchronous alarm OBs 2 ● Number of startup OBs 100 ● Number of asynchronous error OBs 4 ● Number of synchronous error OBs 2 ● Number of diagnostic alarm OBs 1 Nesting depth   ● per priority class 24 Counters, timers and their retentivity   S7 counter   ● Number 2 048 Retentivity   — adjustable Yes IEC counter   ● Number Any (only limited by the main memory) Retentivity   — adjustable Yes S7 times   ● Number 2 048 Retentivity   — adjustable Yes IEC timer   ● Number Any (only limited by the main memory) Retentivity   — adjustable Yes Data areas and their retentivity   Retentive data area (incl. timers, counters, flags), max. 128 kbyte; Available retentive memory for bit memories, timers, counters, DBs, and technology data (axes): 88 KB Flag   ● Number, max. 16 kbyte ● Number of clock memories 8; 8 clock memory bits, grouped into one clock memory byte Data blocks   ● Retentivity adjustable Yes ● Retentivity preset No Local data   ● per priority class, max. 64 kbyte; max. 16 KB per block Address area   Number of IO modules 2 048; max. number of modules / submodules I/O address area   ● Inputs 32 kbyte; All inputs are in the process image ● Outputs 32 kbyte; All outputs are in the process image per integrated IO subsystem   — Inputs (volume) 8 kbyte — Outputs (volume) 8 kbyte per CM/CP   — Inputs (volume) 8 kbyte — Outputs (volume) 8 kbyte Subprocess images   ● Number of subprocess images, max. 32 Address space per module   ● Address space per module, max. 288 byte; For input and output data respectively Address space per station   ● Address space per station, max. 2 560 byte; for central inputs and outputs; depending on configuration; 2 048 bytes for ET 200SP modules + 512 bytes for ET 200AL modules Hardware configuration   Number of distributed IO systems 32; A distributed I/O system is characterized not only by the integration of distributed I/O via PROFINET or PROFIBUS communication modules, but also by the connection of I/O via AS-i master modules or links (e.g. IE/PB-Link) Number of DP masters   ● Via CM 1 Number of IO Controllers   ● integrated 1 ● Via CM 0 Rack   ● Modules per rack, max. 80; CPU + 64 modules + server module (mounting width max. 1 m) + 16 ET 200AL modules ● Number of lines, max. 1 PtP CM   ● Number of PtP CMs the number of connectable PtP CMs is only limited by the number of available slots Time of day   Clock   ● Type Hardware clock ● Backup time 6 wk; At 40 °C ambient temperature, typically ● Deviation per day, max. 10 s; Typ.: 2 s Operating hours counter   ● Number 16 Clock synchronization   ● supported Yes ● to DP, master Yes; Via CM DP module ● to DP, slave Yes; Via CM DP module ● in AS, master Yes ● in AS, slave Yes ● on Ethernet via NTP Yes Interfaces   Number of PROFINET interfaces 1 Number of PROFIBUS interfaces 1; Via CM DP module With optical interface Yes; via BusAdapter 1. Interface   Interface types   ● Number of ports 3; 1. integr. + 2. via BusAdapter ● integrated switch Yes ● RJ 45 (Ethernet) Yes; X1 P3; opt. X1 P1 and X1 P2 via BusAdapter BA 2x RJ45 ● BusAdapter (PROFINET) Yes; Compatible BusAdapter: BA 2x RJ45, BA 2x FC, BA 2x SCRJ, BA SCRJ / RJ45, BA SCRJ / FC, BA 2x LC, BA LC / RJ45, BA LC / FC Functionality   ● IP protocol Yes; *4 ● PROFINET IO Controller Yes ● PROFINET IO Device Yes ● SIMATIC communication Yes ● Open IE communication Yes ● Web server Yes ● Media redundancy Yes PROFINET IO Controller   Services   — PG/OP communication Yes — S7 routing Yes — Isochronous mode Yes — Open IE communication Yes — IRT Yes — MRP Yes; As MRP redundancy manager and/or MRP client; max. number of devices in the ring: 50 — MRPD Yes; Requirement: IRT — PROFIenergy Yes — Prioritized startup Yes; Max. 32 PROFINET devices — Number of connectable IO Devices, max. 128; In total, up to 512 distributed I/O devices can be connected via AS-i, PROFIBUS or PROFINET — Of which IO devices with IRT, max. 64 — Number of connectable IO Devices for RT, max. 128 — of which in line, max. 128 — Number of IO Devices that can be simultaneously activated/deactivated, max. 8; in total across all interfaces — Number of IO Devices per tool, max. 8 — Updating times The minimum value of the update time also depends on communication share set for PROFINET IO, on the number of IO devices, and on the quantity of configured user data Update time for IRT   — for send cycle of 250 µs 250 μs to 4 ms; Note: In the case of IRT with isochronous mode, the minimum update time of 500 µs of the isochronous OB is decisive — for send cycle of 500 µs 500 µs to 8 ms — for send cycle of 1 ms 1 ms to 16 ms — for send cycle of 2 ms 2 ms to 32 ms — for send cycle of 4 ms 4 ms to 64 ms — With IRT and parameterization of "odd" send cycles Update time = set "odd" send clock (any multiple of 125 µs: 375 µs, 625 µs ... 3 875 µs) Update time for RT   — for send cycle of 250 µs 250 µs to 128 ms — for send cycle of 500 µs 500 µs to 256 ms — for send cycle of 1 ms 1 ms to 512 ms — for send cycle of 2 ms 2 ms to 512 ms — for send cycle of 4 ms 4 ms to 512 ms PROFINET IO Device   Services   — PG/OP communication Yes — S7 routing Yes — Isochronous mode No — Open IE communication Yes — IRT Yes — MRP Yes — MRPD Yes; Requirement: IRT — PROFIenergy Yes — Shared device Yes — Number of IO Controllers with shared device, max. 4 2. Interface   Interface types   ● Number of ports 1 ● RS 485 Yes; Via CM DP module Functionality   ● PROFIBUS DP master Yes ● PROFIBUS DP slave Yes ● SIMATIC communication Yes Interface types   RJ 45 (Ethernet)   ● 100 Mbps Yes ● Autonegotiation Yes ● Autocrossing Yes ● Industrial Ethernet status LED Yes RS 485   ● Transmission rate, max. 12 Mbit/s Protocols   Number of connections   ● Number of connections, max. 128; via integrated interfaces of the CPU and connected CPs / CMs ● Number of connections reserved for ES/HMI/web 10 ● Number of connections via integrated interfaces 88 ● Number of connections per CP/CM 32 ● Number of S7 routing paths 16 SIMATIC communication   ● S7 communication, as server Yes ● S7 communication, as client Yes ● User data per job, max. See online help (S7 communication, user data size) Open IE communication   ● TCP/IP Yes — Data length, max. 64 kbyte — several passive connections per port, supported Yes ● ISO-on-TCP (RFC1006) Yes — Data length, max. 64 kbyte ● UDP Yes — Data length, max. 1 472 byte — UDP multicast Yes; Max. 5 multicast circuits ● DHCP No ● SNMP Yes ● DCP Yes ● LLDP Yes Web server   ● HTTP Yes; Standard and user pages ● HTTPS Yes; Standard and user pages PROFIBUS DP master   ● Number of connections, max. 48 Services   — PG/OP communication Yes — S7 routing Yes — Data record routing Yes — Isochronous mode No — Equidistance No — Number of DP slaves 125; In total, up to 512 distributed I/O devices can be connected via AS-i, PROFIBUS or PROFINET — Activation/deactivation of DP slaves Yes OPC UA   ● OPC UA Server Yes; Data access (read, write, subscribe), runtime license required — Application authentication Yes — Security policies Available security policies: None, Basic128Rsa15, Basic256Rsa15, Basic256Sha256 — User authentication "anonymous" or by user name & password Further protocols   ● MODBUS Yes; MODBUS TCP Media redundancy   ● Switchover time on line break, typ. 200 ms; For MRP, bumpless for MRPD ● Number of stations in the ring, max. 50 Isochronous mode   Isochronous operation (application synchronized up to terminal) Yes; Only with PROFINET; with minimum OB 6x cycle of 625 µs S7 message functions   Number of login stations for message functions, max. 32 Program alarms Yes Number of configurable program alarms 5 000 Number of simultaneously active program alarms   ● Number of program alarms 300 ● Number of alarms for system diagnostics 100 ● Number of alarms for motion technology objects 80 Test commissioning functions   Joint commission (Team Engineering) Yes; Parallel online access possible for up to 3 engineering systems Status block Yes; Up to 8 simultaneously (in total across all ES clients) Single step No Status/control   ● Status/control variable Yes ● Variables Inputs/outputs, memory bits, DBs, distributed I/Os, timers, counters ● Number of variables, max.   — of which status variables, max. 200; per job — of which control variables, max. 200; per job Forcing   ● Forcing Yes ● Forcing, variables Peripheral inputs/outputs ● Number of variables, max. 200 Diagnostic buffer   ● present Yes ● Number of entries, max. 1 000 — of which powerfail-proof 500 Traces   ● Number of configurable Traces 4; Up to 512 KB of data per trace are possible Interrupts/diagnostics/status information   Diagnostics indication LED   ● RUN/STOP LED Yes ● ERROR LED Yes ● MAINT LED Yes ● Monitoring of the supply voltage (PWR-LED) Yes ● Connection display LINK TX/RX Yes Supported technology objects   Motion Control Yes; Note: The number of axes affects the cycle time of the PLC program; selection guide via the TIA Selection Tool or SIZER ● Number of available Motion Control resources for technology objects (except cam disks) 800 ● Required Motion Control resources   — per speed-controlled axis 40 — per positioning axis 80 — per synchronous axis 160 — per external encoder 80 — per output cam 20 — per cam track 160 — per probe 40 ● Positioning axis   — Number of positioning axes at motion control cycle of 4 ms (typical value) 5 — Number of positioning axes at motion control cycle of 8 ms (typical value) 10 Controller   ● PID_Compact Yes; Universal PID controller with integrated optimization ● PID_3Step Yes; PID controller with integrated optimization for valves ● PID-Temp Yes; PID controller with integrated optimization for temperature Counting and measuring   ● High-speed counter Yes Ambient conditions   Ambient temperature during operation   ● horizontal installation, min. 0 °C ● horizontal installation, max. 60 °C ● vertical installation, min. 0 °C ● vertical installation, max. 50 °C Ambient temperature during storage/transportation   ● min. -40 °C ● max. 70 °C Configuration   Programming   Programming language   — LAD Yes — FBD Yes — STL Yes — SCL Yes — GRAPH Yes Know-how protection   ● User program protection/password protection Yes ● Copy protection Yes ● Block protection Yes Access protection   ● Protection level: Write protection Yes ● Protection level: Read/write protection Yes ● Protection level: Complete protection Yes Cycle time monitoring   ● lower limit adjustable minimum cycle time ● upper limit adjustable maximum cycle time Dimensions   Width 100 mm Height 117 mm Depth 75 mm Weights   Weight, approx. 310 g

  全部关于 CPU 1512SP-1 PN 产品与解决方案在线目录与订购系统技术信息服务与支持与合作伙伴服务项目