上海朔川电气设备有限公司

免费会员

您现在的位置：上海朔川电气设备有限公司>>西门子S7-1500>> 西门子6ES75225FH000AB0型号及参数

西门子6ES75225FH000AB0型号及参数

参考价:	面议

参考价:

面议

具体成交价以合同协议为准

产品型号
品牌
经销商 厂商性质
上海市 所在地

访问次数：799更新时间：2017-10-20 20:31:55

在线询价加入对比查看联系方式

联系我们时请说明是智能制造网上看到的信息，谢谢!

西门子S7-1500

上海朔川电气设备有限公司

免费会员·9年

联系人：: 吉梦琪

在线咨询给我留言

扫一扫访问手机商铺

产品简介

西门子6ES75225FH000AB0型号及参数

产品介绍

西门子6ES75225FH000AB0型号及参数 西门子6ES75225FH000AB0型号及参数

6ES7522-5FH00-0AB0

SIMATIC S7-1500, 数字量输出模块 DQ 16xAC 230V/1A;TRIAC; 16 通道 8 个一组; 2A 每组; 替换值

· 公司名称：上海朔川电气设备有限公司

· 联系人：吉梦琪

· 手机；

· ：

· 地址：上海市金山区泾波路680号

· ：2840735331

SM 522 数字量输出模块

订货数据
附件
产品信息
组态工具

跳转到

概述

应用

设计

功能

技术规范

概述

8、16 和 32 通道数字量输出模块
灵活地选择控制器以满足相应任务需要
用于使用附加输出对系统进行后续扩展
35 mm 宽的模块具有参数设置和诊断功能
25 mm 宽的模块可在狭小空间内使用：极为经济，无参数设置或诊断功能

应用

数字量输出模块可以切换设备中的 24 V DC 或 230 V AC 电压，从而可将内部信号从控制器传输至设备。可以连接电磁阀、直流接触器和指示灯。

35 mm 宽的输出模块具有可设定的参数和诊断功能，因此可根据相应过程要求进行灵活调整。

25 mm 宽的输出模块没有可设定的参数或诊断功能，因此可极为方便地集成到工程系统中。建议将它们在只需要很少输入通道的位置使用，或在必须在十分有限的空间内部署大量通道的情况下使用。

根据需要，可在一个站中并排使用两种模块。由于具有统一特性并采用共同的系统附件，处理十分方便。

提供了以下宽度为 35 mm 的数字量输出模块：

DQ 16x24VDC/0.5A ST；
数字量输出模块，16 通道 24 VDC / 0.5 A（晶体管）；两个电压组；每组 4 A；可设置诊断功能；可设置输出替代值
DQ 32x24VDC/0.5A ST；
数字量输出模块，32 通道 24 VDC / 0.5 A（晶体管）；四个电压组；每组 4 A；可设置诊断功能；可设置输出替代值
DQ 8x24VDC/2A HF;
数字量输出模块，8 通道 24 VDC / 2 A（晶体管）；四个电压组；每组 8 A；可设置诊断功能；可设置输出替代值
DQ 8x230VAC/2A ST;
数字量输出模块，8 通道 230 VAC / 2 A（晶体管）；八个电压组；每组 2 A；可设置诊断功能；可设置输出替代值
DQ 8x230VAC/5A ST;
带有 8 点输出的数字量输出模块，230 V AC/5 A（继电器）；8 个电压组；每组 5 A；可设置输出的替代值

提供了以下宽度为 25 mm 的数字量输出模块：

DQ 16x24VDC/0.5A BA;
带有 16 个通道的数字量输出模块，24 VDC/0.5 A（晶体管）；源型输出；两个电压组 4A
DQ 32x24VDC/0.5A BA;
带有 16 个通道的数字量输出模块，24 VDC/0.5 A（晶体管）；源型输出；四个电压组；每组 4 A

设计

用一个螺丝安装在 S7-1500 安装导轨上
35 mm 模块采用螺钉型端子或推入式端子的标准化 40 针前连接器（不能用于 25 mm 模块）
25 mm 模块采用推入式端子的标准化 40 针前连接器（不能用于 35 mm 模块）
标准化、协调型前连接器针脚分配，更便于接线
可连接芯线截面积0.25 mm² 至 1.5 mm²（AWG24 至 16）
集成式电压桥接件，用于灵活形成电压组(仅 35 mm 模块)
前连接器的预接线位置
前盖带有可扩充的电缆室，即使*接线时也如此
模块正面的清晰标签
- 模块类型
- 订货号
- 硬件和固件型号
- 通道编号标签
- 电缆连接图

含在供货范围之内：

用于手工贴标签的一个标签条
一个 U 型连接器
印制有文字的前门
前连接器（(仅 25 mm 模块）

功能

统一的显示和诊断方式：
- 故障（红色 LED）和运行（绿色 LED）模块状态显示
- 用于信号状态日志的信号状态显示。"0" 和日志。"1"（绿色 LED）或短路指示（红色 LED）
- 显示 24 V DC 电源电压（绿色 LED）
支持的功能：
- 识别和维护数据 IM0 至 IM3
- 固件更新
- 与通道有关的参数分配（* HF 模块）
- 按通道进行诊断（* HF 模块）
- 等时同步模式（取决于模块）
- 可以为输出设置替换值（*于 35 mm 模块）

技术规范

Article number	6ES7522-1BH01-0AB0	6ES7522-1BL01-0AB0	6ES7522-1BF00-0AB0	6ES7522-5EH00-0AB0
	S7-1500, DQ 16X24V DC/0.5A HF	S7-1500, DQ 32X24VDC/0.5A HF	S7-1500, DQ 8X24VDC/2A HF	S7-1500, DQ 16X24...48VUC/125VDC/0.5A ST
General information
Product type designation	DQ 16x24VDC/0.5A HF	DQ 32x24VDC/0.5A HF	DQ 8x24VDC/2A HF
HW functional status	FS01	FS01	FS01	FS01
Firmware version	V1.0.0	V1.0.0	V2.1.0	V1.0.0
● FW update possible	Yes		Yes	Yes
Product function
● I&M data	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3
Engineering with
● STEP 7 TIA Portal configurable/integrated as of version	V13 SP1 / -	V13 SP1 / -	V13 SP1 / -	V13 SP1 / -
● STEP 7 configurable/integrated as of version			V5.5 SP3 / -	V5.5 SP3 / -
● PROFIBUS as of GSD version/GSD revision	V1.0 / V5.1	V1.0 / V5.1	V1.0 / V5.1	V1.0 / V5.1
● PROFINET as of GSD version/GSD revision	V2.3 / -	V2.3 / -	V2.3 / -	V2.3 / -
Operating mode
● DQ	Yes	Yes	Yes	Yes
● DQ with energy-saving function	No	No	Yes; with an application	No
● PWM	No	No	Yes	No
● Oversampling	No	No	No	No
● MSO	Yes	Yes	Yes	Yes
Supply voltage
Rated value (DC)	24 V	24 V	24 V
permissible range, lower limit (DC)	20.4 V	20.4 V	20.4 V
permissible range, upper limit (DC)	28.8 V	28.8 V	28.8 V
Reverse polarity protection	Yes; through internal protection with 7 A per group	Yes; through internal protection with 7 A per group	Yes; through internal protection with 10 A per group
Input current
Current consumption, max.	30 mA	60 mA	40 mA; 20 mA per group, no output is activated.
Output voltage
Rated value (DC)	24 V	24 V	24 V	24 V; 48 V, 125 V
Rated value (AC)				24 V; 48 V (50 - 60 Hz)
Power
Power available from the backplane bus	1.1 W	1.1 W	0.9 W	2 W
Power loss
Power loss, typ.	2 W	3.5 W	5.6 W; 6.8 W for PWM operation	3.8 W
Digital outputs
Type of digital output	Transistor	Transistor	Transistor	Transistor
Number of digital outputs	16	32	8	16
Current-sinking				Yes
Current-sourcing	Yes	Yes	Yes	Yes
Short-circuit protection	Yes; Clocked electronically	Yes; Clocked electronically	Yes
● Response threshold, typ.	1 A	1 A	3 A
Limitation of inductive shutdown voltage to	L+ (-53 V)	L+ (-53 V)	-17 V	200 V (suppressor diode)
Controlling a digital input	Yes	Yes	Yes	Yes
Digital output functions, parameterizable
● Freely usable digital output			Yes
● PWM output			Yes
— Number, max.			2
— Cycle duration, parameterizable			Yes; 2 ... 100 ms continuous
— ON period, min.			0 %
— ON period, max.			100 %
— Resolution of the duty cycle			0.1 %
— Minimum pulse duration			300 µs
Switching capacity of the outputs
● with resistive load, max.	0.5 A	0.5 A		0.5 A
● on lamp load, max.	5 W	5 W	10 W	40 W; At 125 V DC, 10 W at 48 V UC, 5 W at 24 V UC
Load resistance range
● lower limit	48 Ω	48 Ω	12 Ω
● upper limit	12 kΩ	12 kΩ	4 kΩ
Output voltage
● for signal "1", min.	L+ (-0.8 V)	L+ (-0.8 V)	L+ (-0.8 V)	L+ (-1.0 V)
Output current
● for signal "1" rated value	0.5 A	0.5 A	2 A	0.5 A
● for signal "1" permissible range, max.	0.5 A	0.5 A	2.4 A; Note derating specification for PWM operation	0.6 A
● for signal "0" residual current, max.	0.5 mA	0.5 mA	0.5 mA
Output delay with resistive load
● "0" to "1", typ.			80 µs
● "0" to "1", max.	100 µs	100 µs	100 µs	5 ms
● "1" to "0", typ.			300 µs
● "1" to "0", max.	500 µs	500 µs	500 µs	5 ms
Parallel switching of two outputs
● for logic links	Yes	Yes	Yes	Yes
● for uprating	No	No	No	No
● for redundant control of a load	Yes	Yes	Yes	Yes
Switching frequency
● with resistive load, max.	100 Hz	100 Hz	100 Hz; With PWM operation: 500 Hz	25 Hz
● with inductive load, max.	0.5 Hz; According to IEC 60947-5-1, DC-13	0.5 Hz; According to IEC 60947-5-1, DC-13	0.5 Hz; According to IEC 60947-5-1, DC-13; max. 500 Hz with PWM operation only with external circuit; see additional description in the manual	0.5 Hz
● on lamp load, max.	10 Hz	10 Hz	10 Hz	10 Hz
Total current of the outputs
● Current per channel, max.	0.5 A; see additional description in the manual	0.5 A; see additional description in the manual	2 A; see additional description in the manual	0.5 A
● Current per group, max.	4 A; see additional description in the manual	4 A; see additional description in the manual	8 A; see additional description in the manual	0.5 A
● Current per module, max.	8 A; see additional description in the manual	16 A; see additional description in the manual	16 A; see additional description in the manual	8 A
Cable length
● shielded, max.	1 000 m	1 000 m	1 000 m	1 000 m
● unshielded, max.	600 m	600 m	600 m	600 m
Isochronous mode
Isochronous operation (application synchronized up to terminal)	Yes	Yes	No	No
Execution and activation time (TCO), min.	70 µs	70 µs
Bus cycle time (TDP), min.	250 µs	250 µs
Interrupts/diagnostics/status information
Diagnostics function	Yes	Yes	Yes	No
Substitute values connectable	Yes	Yes	Yes	Yes
Alarms
● Diagnostic alarm	Yes	Yes	Yes	No
Diagnostic messages
● Monitoring the supply voltage	Yes	Yes	Yes	No
● Wire-break	Yes	Yes	No	No
● Short-circuit	Yes	Yes	Yes	No
● Group error	Yes	Yes	Yes
Diagnostics indication LED
● RUN LED	Yes; Green LED	Yes; Green LED	Yes; Green LED	Yes; Green LED
● ERROR LED	Yes; Red LED	Yes; Red LED	Yes; Red LED	Yes; Red LED
● Monitoring of the supply voltage (PWR-LED)	Yes; Green LED	Yes; Green LED	Yes; Green LED	No
● Channel status display	Yes; Green LED	Yes; Green LED	Yes; Green LED	Yes; Green LED
● for channel diagnostics	Yes; Red LED	Yes; Red LED	Yes; Red LED	No
● for module diagnostics	Yes; Red LED	Yes; Red LED	Yes; Red LED	Yes; Red LED
Potential separation
Potential separation channels
● between the channels	No	No	No	Yes
● between the channels, in groups of	8	8	4	1
● between the channels and backplane bus	Yes	Yes	Yes	Yes
Permissible potential difference
between different circuits				125 V DC/48 V AC
Isolation
Isolation tested with	707 V DC (type test)	707 V DC (type test)	707 V DC (type test)	2 000 V DC
Ambient conditions
Ambient temperature during operation
● horizontal installation, min.	0 °C			0 °C
● horizontal installation, max.	60 °C			60 °C
● vertical installation, min.	0 °C			0 °C
● vertical installation, max.	60 °C			40 °C
Decentralized operation
Prioritized startup	Yes	Yes	Yes	Yes
Dimensions
Width	35 mm	35 mm	35 mm	35 mm
Height	147 mm	147 mm	147 mm	147 mm
Depth	129 mm	129 mm	129 mm	129 mm
Weights
Weight, approx.	230 g	280 g	240 g	230 g

Article number	6ES7522-5HF00-0AB0	6ES7522-5HH00-0AB0	6ES7522-5FF00-0AB0	6ES7522-5FH00-0AB0
	S7-1500, DQ 8X230VAC/5A ST (RELAY)	S7-1500, DQ 16X230VAC/2A ST (RELAY)	S7-1500, DQ 8X230VAC/2A ST (TRIAC)	S7-1500, DQ 16X230VAC/1A ST (TRIAC)
General information
Product type designation			DQ 8x230 V AC/2A ST (triac)	DQ 16x230VAC/1A ST (Triac)
HW functional status	FS01	FS01	FS01	FS01
Firmware version	V2.0.0	V1.0.0	V2.0.0	V1.0.0
● FW update possible	Yes	Yes	Yes	Yes
Product function
● I&M data	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3
Engineering with
● STEP 7 TIA Portal configurable/integrated as of version	V12 / V12	V13 SP1 / -	V12 / V12	V13 SP1 / -
● STEP 7 configurable/integrated as of version	V5.5 SP3 / -	V5.5 SP3 / -	V5.5 SP3 / -	V5.5 SP3 / -
● PROFIBUS as of GSD version/GSD revision	V1.0 / V5.1	V1.0 / V5.1	V1.0 / V5.1	V1.0 / V5.1
● PROFINET as of GSD version/GSD revision	V2.3 / -	V2.3 / -	V2.3 / -	V2.3 / -
Operating mode
● DQ	Yes	Yes	Yes	Yes
● DQ with energy-saving function	No	No	No	No
● PWM	No	No	No	No
● Oversampling	No	No	No	No
● MSO	Yes	Yes	Yes	Yes
Supply voltage
Rated value (DC)	24 V	24 V
permissible range, lower limit (DC)	20.4 V	20.4 V
permissible range, upper limit (DC)	28.8 V	28.8 V
Reverse polarity protection	Yes	Yes
Input current
Current consumption, max.	80 mA	150 mA
Output voltage
Rated value (AC)	230 V; 24 V DC to 120 V DC / 24 V AC to 230 V AC	230 V; 24 V DC to 120 V DC / 24 V AC to 230 V AC	230 V; 120/230V AC, 50/60 Hz	230 V; 120/230V AC, 50/60 Hz
Power
Power available from the backplane bus	0.8 W	0.8 W	0.9 W	1.2 W
Power loss
Power loss, typ.	5 W	5 W	10.8 W	11.1 W
Digital outputs
Type of digital output	Relays	Relays	Triac	Triac
Number of digital outputs	8	16	8	16
Current-sinking	Yes	Yes		Yes
Current-sourcing	Yes	Yes	Yes	Yes
Short-circuit protection	No	No	No	No
Controlling a digital input	possible	Yes
Switching capacity of the outputs
● with resistive load, max.			2 A	1 A
● on lamp load, max.	1 500 W; 10 000 operating cycles	50 W (230 V AC), 5 W (24 V DC)	50 W	50 W
● Low energy/fluorescent lamps with electronic control gear	10x 58 W (25 000 operating cycles)
● Fluorescent tubes, conventionally compensated	1x 58 W (25 000 operating cycles)
● Fluorescent tubes, uncompensated	10x 58 W (25 000 operating cycles)
Output voltage
● for signal "1", min.			L1 (-1.5 V) at maximum output current; L1 (-8.5 V) at minimum output current	L1 (-1.5 V) at maximum output current; L1 (-8.5 V) at minimum output current
Output current
● for signal "1" rated value	5 A	2 A	2 A	1 A
● for signal "1" permissible range, min.	5 mA; 10 V	10 mA; 10 V	10 mA	10 mA
● for signal "1" permissible range, max.	8 A; thermal continuous current	2 A; thermal continuous current	15 A; max. 1 AC cycle	15 A; max. 1 AC cycle
● for signal "0" residual current, max.	0 A	0 A	2 mA	2 mA
Output delay with resistive load
● "0" to "1", max.			1 AC cycle	1 AC cycle
● "1" to "0", max.			1 AC cycle	1 AC cycle
Parallel switching of two outputs
● for logic links	Yes	Yes	No	No
● for uprating	No	No	No	No
● for redundant control of a load	Yes	Yes	Yes	Yes
Switching frequency
● with resistive load, max.	2 Hz	1 Hz	10 Hz	10 Hz
● with inductive load, max.	0.5 Hz	0.5 Hz	0.5 Hz	0.5 Hz
● on lamp load, max.	2 Hz	1 Hz	1 Hz	1 Hz
Total current of the outputs
● Current per channel, max.	8 A; see additional description in the manual	2 A; see additional description in the manual	2 A; see additional description in the manual	1 A; see additional description in the manual
● Current per group, max.	8 A; see additional description in the manual	4 A; see additional description in the manual	2 A; see additional description in the manual	2 A; see additional description in the manual
● Current per module, max.	64 A; see additional description in the manual	32 A; see additional description in the manual	10 A; see additional description in the manual	10 A; see additional description in the manual
Relay outputs
● Number of relay outputs	8	16
● Rated supply voltage of relay coil L+ (DC)	24 V	24 V
● Current consumption of relays (coil current of all relays), typ.	80 mA	150 mA
● external protection for relay outputs	With miniature circuit breaker with characteristic B for: cos φ 1.0: 600 A cos φ 0.5 ... 0.7: 900 A with 8 A Diazed fuse: 1000 A	Miniature circuit breaker B10 / B16
● Contact connection (internal)	No	No
● Size of motor starters according to NEMA, max.	5	5
● Number of operating cycles, max.	4 000 000; see additional description in the manual	see additional description in the manual
● Relay approved acc. to UL 508	Yes; 250 V AC/5 A g.p.; 120 V AC TV-4 tungsten; A300, R300	No
Switching capacity of contacts
— with inductive load, max.	see additional description in the manual	2 A; see additional description in the manual
— with resistive load, max.	see additional description in the manual	2 A; see additional description in the manual
Triac outputs
● Size of motor starters according to NEMA, max.			5	4
Cable length
● shielded, max.	1 000 m	1 000 m	1 000 m	1 000 m
● unshielded, max.	600 m	600 m	600 m	600 m
Isochronous mode
Isochronous operation (application synchronized up to terminal)	No	No	No	No
Interrupts/diagnostics/status information
Diagnostics function	Yes	Yes	No	No
Substitute values connectable	Yes	Yes	Yes	Yes
Alarms
● Diagnostic alarm	Yes	Yes	No	No
Diagnostic messages
● Monitoring the supply voltage	Yes	Yes	No	No
● Wire-break	No	No	No	No
● Short-circuit	No	No	No	No
Diagnostics indication LED
● RUN LED	Yes; Green LED	Yes; Green LED	Yes; Green LED	Yes; Green LED
● ERROR LED	Yes; Red LED	Yes; Red LED	Yes; Red LED	Yes; Red LED
● Monitoring of the supply voltage (PWR-LED)	Yes; Green LED	Yes; Green LED	No	No
● Channel status display	Yes; Green LED	Yes; Green LED	Yes; Green LED	Yes; Green LED
● for channel diagnostics	No	No	No	No
● for module diagnostics	Yes; Red LED	Yes; Red LED	Yes; Red LED	Yes; Red LED
Potential separation
Potential separation channels
● between the channels	Yes; Switching of different phases permitted	No	Yes	No
● between the channels, in groups of	1	2	1	2
● between the channels and backplane bus	Yes	Yes	Yes	Yes
● Between the channels and load voltage L+	Yes	Yes
● Between the channels and load voltage L1			Yes
Permissible potential difference
between different circuits	250 V AC between the channels and the supply voltage L+; 250 V AC between the channels and the backplane bus; 500 V AC between the channels	250 V AC between the channels and the supply voltage L+; 250 V AC between the channels and the backplane bus; 500 V AC between the channels	250 V AC between the channels and the backplane bus; 500 V AC between the channels	250 V AC between the channels and the backplane bus; 500 V AC between the channels
Isolation
Isolation tested with	Between channels: 3 100 V DC; between channels backplane bus: 3 100 V DC; between L+ and backplane bus: 707 V DC (type test)	Between channels: 3 100 V DC; between channels backplane bus: 3 100 V DC; between L+ and backplane bus: 707 V DC (type test)	3 100 V DC	3 100 V DC
Ambient conditions
Ambient temperature during operation
● horizontal installation, min.	0 °C	0 °C	0 °C	0 °C
● horizontal installation, max.	60 °C	60 °C	60 °C	60 °C
● vertical installation, min.	0 °C	0 °C	0 °C	0 °C
● vertical installation, max.	40 °C	40 °C	40 °C	60 °C
Decentralized operation
Prioritized startup	Yes	Yes	Yes	Yes
Dimensions
Width	35 mm	35 mm	35 mm	35 mm
Height	147 mm	147 mm	147 mm	147 mm
Depth	129 mm	129 mm	129 mm	129 mm
Weights
Weight, approx.	350 g	350 g	290 g	310 g

Article number	6ES7522-1BH10-0AA0	6ES7522-1BL10-0AA0
	S7-1500, DQ 16X24VDC/0.5A BA	S7-1500, DQ 32X24VDC/0.5A BA
General information
Product type designation	DQ 16x24VDC/0.5A BA	DQ 32x24VDC/0.5A BA
HW functional status	FS01	FS01
Firmware version	V1.0.0	V1.0.0
● FW update possible	Yes	Yes
Product function
● I&M data	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3
Engineering with
● STEP 7 TIA Portal configurable/integrated as of version	V13 / V13	V13 / V13
● STEP 7 configurable/integrated as of version	V5.5 SP3 / -	V5.5 SP3 / -
● PROFIBUS as of GSD version/GSD revision	V1.0 / V5.1	V1.0 / V5.1
● PROFINET as of GSD version/GSD revision	V2.3 / -	V2.3 / -
Operating mode
● DQ	Yes	Yes
● DQ with energy-saving function	No	No
● PWM	No	No
● Oversampling	No	No
● MSO	Yes	Yes
Supply voltage
Rated value (DC)	24 V	24 V
permissible range, lower limit (DC)	20.4 V	20.4 V
permissible range, upper limit (DC)	28.8 V	28.8 V
Reverse polarity protection	Yes; through internal protection with 7 A per group	Yes; through internal protection with 7 A per group
Input current
Current consumption, max.	30 mA	60 mA
Output voltage
Rated value (DC)	24 V	24 V
Power
Power available from the backplane bus	1.15 W	1.15 W
Power loss
Power loss, typ.	2.2 W	3.8 W
Digital outputs
Type of digital output	Transistor	Transistor
Number of digital outputs	16	32
Current-sourcing	Yes	Yes
Short-circuit protection	Yes	Yes
● Response threshold, typ.	1 A	1 A
Limitation of inductive shutdown voltage to	L+ (-53 V)	L+ (-53 V)
Controlling a digital input	Yes	Yes
Switching capacity of the outputs
● with resistive load, max.	0.5 A	0.5 A
● on lamp load, max.	5 W	5 W
Load resistance range
● lower limit	48 Ω	48 Ω
● upper limit	12 kΩ	12 kΩ
Output voltage
● for signal "1", min.	L+ (-0.8 V)	L+ (-0.8 V)
Output current
● for signal "1" rated value	0.5 A	0.5 A
● for signal "1" permissible range, max.	0.5 A	0.5 A
● for signal "0" residual current, max.	0.5 mA	0.5 mA
Output delay with resistive load
● "0" to "1", max.	100 µs	100 µs
● "1" to "0", max.	500 µs	500 µs
Parallel switching of two outputs
● for logic links	Yes	Yes
● for uprating	No	No
● for redundant control of a load	Yes	Yes
Switching frequency
● with resistive load, max.	100 Hz	100 Hz
● with inductive load, max.	0.5 Hz; According to IEC 60947-5-1, DC-13	0.5 Hz; According to IEC 60947-5-1, DC-13
● on lamp load, max.	10 Hz	10 Hz
Total current of the outputs
● Current per channel, max.	0.5 A; see additional description in the manual	0.5 A; see additional description in the manual
● Current per group, max.	4 A; see additional description in the manual	4 A; see additional description in the manual
● Current per module, max.	8 A; see additional description in the manual	16 A; see additional description in the manual
Cable length
● shielded, max.	1 000 m	1 000 m
● unshielded, max.	600 m	600 m
Isochronous mode
Isochronous operation (application synchronized up to terminal)	No	No
Interrupts/diagnostics/status information
Diagnostics function	No	No
Substitute values connectable	No	No
Alarms
● Diagnostic alarm	No	No
Diagnostic messages
● Monitoring the supply voltage	No	No
● Wire-break	No	No
● Short-circuit	No	No
● Group error	No	No
Diagnostics indication LED
● RUN LED	Yes; Green LED	Yes; Green LED
● ERROR LED	Yes; Red LED	Yes; Red LED
● Monitoring of the supply voltage (PWR-LED)	Yes; Green LED	Yes; Green LED
● Channel status display	Yes; Green LED	Yes; Green LED
● for channel diagnostics	No	No
● for module diagnostics	No	No
Potential separation
Potential separation channels
● between the channels	No	No
● between the channels, in groups of	8	8
● between the channels and backplane bus	Yes	Yes
Isolation
Isolation tested with	707 V DC (type test)	707 V DC (type test)
Decentralized operation
Prioritized startup	Yes	Yes
Dimensions
Width	25 mm	25 mm
Height	147 mm	147 mm
Depth	129 mm	129 mm
Weights
Weight, approx.	230 g	280 g
Other
Note:	Supplied incl. 40-pole push-in front connectors	Supplied incl. 40-pole push-in front connectors