| SM2-D1024-80-GB-12 VisionCam PS Type 1* |
| 图像传感器 | Photonfocus A1024B (2. Generation) |
| 技术 | CMOS主动像元技术 |
| 扫描模式 | 逐行扫描 |
| 光学尺寸 | 1” (15.42 mm diagonal) |
| 分辨率 | 1024 x 1024像素 |
| 像元尺寸 | 10.6 µm x 10.6 µm |
| 有效感光区域 | 10.9 mm x 10.9 mm (maximum) |
| 暗电流 | 2 fA/pixel @ 30°C |
| 满阱容量 | ~200 ke¯ |
| 光谱范围 | < 400="" to="" 900=""> |
| 灵敏度 | 120 x 10³ DN / (J/m²) @ 610 nm / 8 bit / gain = 1
(approximay 350 DN / (lux s) @ 610 nm / 8 bit / gain = 1) |
| 量子效应 | 45 % @ 550 nm |
| 填充因子 | 35 % (geometrical) |
| 动态范围 | 60 dB in linear mode; 120 dB with LinLog® |
| 色彩模式 | 黑白 |
| 特性曲线 | Linear, LinLog®,Skimming |
| 快门模式 | 全局快门 |
| 读出模式 | Sequential or simultaneous read out (read out during exposure) |
| 曝光时间 | 10 µs … 0.83 s / 50 ns steps |
| 帧频 | 75 fps |
| 像素时钟 | 40 MHz |
| 数据通道 | 2 (internal) |
| 固定模式噪声 | < 1="" dn="" rms="" @="" 8="" bit="" gain="1" offset="" correction=""> |
| 灰度分辨率 | 8 bit / 10 bit/ 12 bit |
| 模拟增益 | 1 |
| 数字增益 | 1 / 2 / 4 |
| 配置接口 | Built-in Webserver |
| 触发模式 | 自运行（无触发）/接口触发/外触发输入 |
| 特点 | • Region of Interest (ROI) • 16 Multiple ROI (MROI) • Decimation Y • Image correction • Look-up table (LUT)
• Constant frame rate • Image information • Peak Detector
• Extended trigger input and strobe output functionality |
| 接口 | GigE |
| 工作温度 | 0°C ... +50°C |
| 供电 | +12 V DC (±10%) |
| 功耗 | 8.0 W |
| 镜头接口 | C口（CS口可选） |
| 尺寸 | 60 x 60 x 127 mm³ |
| 重量 | 532 g |
| 相机控制 | Built-in webserver |
SM2-D1024-TI6455-80-GB-12 CMOS DSP Camera
Features
The smart camera SM2-D1024-TI6455-80-GB-12 is based on the Photonfocus CMOS image sensor A1024B. This Photonfocus CMOS sensor with a full well capacity (FWC) of 200 ke- is optimized for high dynamic range applications and a high signal to noise ratio (SNR). In the smart camera SM2-D1024-TI6455-80-GB-12 a 1.2 GHz DSP from Texas Instruments (TI) and several interfaces are implemented.
In the development several software and debugging tools could be used. A frame work and examples helps to setup the complete application with the smart camera SM2-D1024-TI6455-80-GB-12. For the image processing own software libraries, open source libraries as OpenCV or Halcon Embedded 9.0 from MvTech could be used.
Camera SM2-D1024-TI6455-80-GB-12
| Speed grade | -80 |
| frame rate | 75 fps |
| Grey Level | 12 Bit |
Sensor Properties Photonfocus A1024B
■ monochrome 1" CMOS image sensor
■ 1024 x 1024 pixel (megapixel resolution)
■ pixel size: 10.6 µm x 10.6 µm
■ Global Shutter
■ spectral range: 400 - 900 nm
■ LinLog® response curve (linear-logarithmic sensor characteristics)
Camera Properties
■ configurable region of interest (ROI)
■ up to 16 selectable windows (Multiple Region of Interest-MROI)
■ image preprocessing with integrated look up tables (LUT)
■ integrated digital reduction of fix pattern noise (FPN)
■ integrated shading correction
■ ultra low trigger delay and low trigger jitter ■ lens mount: C-Mount (option CS-Mount)
■ MV1 form factor: 60 x 60 mm² (W x H)
DSP Module Properties TMS320C6455 ■ High performance fixed point DSP TMS320C6455
■ 0.83 ns instruction cycle, 1.2 GHz clock
■ Eight 32-Bit instructions/cycle
■ 9600 MIPS/MMACS (16 Bit)
■ 512 MB SDRAM
■ 2GB SD card
■ JTAG program interface
■ Isolated inputs and outputs
■ RS422 interface
■ GigE Interface, configurable for 10/100 MByte/s Ethernet
This camera focus on demanding applications in industrial image processing where an embedded system is an alternative to PC system approaches. The camera with LinLog® sensor technology offers an extraordinary wide dynamic range and a high framerate combined with high resolution. Due to the global shutter of the sensor, even high-speed applications with exposure times in the µs-area are possible. The implemented high performance DSP TMS320C6455 from Texas Instruments (TI) enables leading edge applications with this embedded system.
For the software development the TI CodeComposerStudio (CCS) is neccessary. Photonfocus supports the newest version 5.3. The single user license (N01D) could be ordered from the TI homepage. For the first steps the 90day evaluation version (CSS-FREE) could be used which has no restrictions. To program the camera a JTAG adapter is necessary which could be ordered together with camera.
Additional information about the CodeComposerStudio (CCS) from TI:
For debugging of the camera system an emulator is needed. The emulator XDS200 from TI is supported by the CCS. Due to the USB interface this emulator could also be used for developments together with notebooks.
Further information about the TI emulator XDS200 could be found here:
The framework and also the examples for the smart camera are based on CCS 5.x. Photonfocus provides also the source code of the framework to enable fast design-in cycles of user inplementations. There are also examples which does not use the framework. These examples show how to use the basic functions of the camera.
On the SM2 microSD card following items are stored:
all needed files for CCS development (framework, source code, libraries, examples) in a zip file,
camera manual and source code documentation,
VIBFinder.exe, this windows tool finds the connected camera if the user does not know the camera IP address,
tcpdisplay.jar, JavaApplet to connect to camera build-in webserver and
Ethernet.ini, to change the camera IP-address, default address is: 192.168.1.240.
Product Availability
SM2-D1024-TI6455-80-GB-12 for sale
JTAG adapter for sale
具体成交价以合同协议为准
免费会员·4年
￥面议
￥面议
￥面议
