PLC 工控机 嵌入式系统 人机界面 工业以太网 现场总线 变频器 机器视觉 DCS PAC/PLMC SCADA 工业软件 ICS信息安全 应用方案 无线通讯
湖北澳星环保成套设备有限公司
湖北澳星环保成套设备有限公司
暂无信息 |
该阀广泛应用于建材、冶金、矿山、电力，化工、玻璃、轻工、粮食等行业，是控制流量、调节或切断粉尘物料的理想设备
该阀广泛应用于建材、冶金、矿山、电力，化工、玻璃、轻工、粮食等行业，是控制流量、调节或切断粉尘物料的理想设备。
The valve is widely used in the building material, metallurgy, mining, electric power chemical, glass, light industry and food industry etc. It is the ideal equipment to control flow, adjust or cut down powder material.
结构特点：
Structure characteristic:
密闭性强、操作灵活、传动部分无污染、无粉尘影响、使用寿命长、无泄漏、安装不受角度影响，能随时开闭，调节物料流量，特别适用于无粘度的固体粉料及小于Φ10mm的颗粒料、晶体料、固状料的输送及流量调节。
This valve is good in seal, handy to open and closing, long life and not leaky. There is no contamination and dust influence in driving part. It can be installed at any angle. It also can be opened and closed at any time to change the flow of material. It is especially suitable for non-glutinosity solid powder and crystalloid, grain, solid material to be transported.
性能参数
Performance parameter
适用温度 Suitable temperature | 公称压力 Nominal pressure | 适用介质 Suitable medium |
≤120℃ | 0.05MPa | 空气、粉尘气体、固体粉料、晶体料 Air, gas with dust, solid powder, crystalloid |
外形图：
Appearance figure:
外形连接尺寸：
Appearance joint dimension:
工作原理：
Working principle
主要由框架、闸板、丝杆、螺母等零件构成，用手转动手轮使丝杆带着丝杆螺母和闸板沿水平方向往复运动，达到闸门的启闭目的。
It is mainly made up of frame, gate board, screw pole, nut etc. Rotate the handwheel by hand, then the screw pole drives the nut and gate board move in horizontal to and fro to open or close the valve.
使用说明：
Usage explanation:
l 本阀可水平安装或垂直安装，安装时两法兰连接中间必须加密封垫片，然后锁紧螺栓。
l 操作时手轮顺时针旋转为阀关，反之为开，不得在手轮上再增加辅助杠杆。
l 若长期存放应使设备处于关闭状态，各传动部位应加润滑油，不允许露天存放或堆置。
l It can be installed in horizontal or vertical. Sealing gasket must be put on the connected, then equably tight the bolt.
l You can not add assistant lever to the hａnd wheel. Clockwise turn of hａnd wheel means the closing of valve, otherwise it means opening.
l The device should be in the shut-down if the valve-board is placed longer. Driving parts should add lubricated oil. Placing in the open air and piling up is not permitted.
订货须知:
Information for order
l 选用订货时，请参照产品样本注明产品规格、型号及技术参数（使用温度、设备工况、介质性质等）。
l 表格中未列规格、用于特殊介质或其它特殊要求，请与我公司经销部、技术部联系，可为您另行设计、制造。
l Please indicate the type, model and technical parameter (using temperature, working condition of equipment and characteristic of medium etc) referring to the product sample when you place an order.
l If you have other special demand, need special medium or the spec that is not listed in the table, please contact with our department of market and technology. We can design and manufacture for you especially.
地址：中国湖北荆州市沙市区十号路98号 Add: No.98, No 10 Road Shashi District Jingzhou Huhei
邮编(Postcode)：434006 (Fax)： 电话(Tel)：0716--4310982
您感兴趣的产品PRODUCTS YOU ARE INTERESTED IN
智能制造网 设计制作，未经允许翻录必究 .
请输入账号
请输入密码
请输验证码
