在世界各地的普通行业及特殊行业都被广泛使用。
化纤行业:如:加弹机 适用于高速(6000m/min)
棉纺织工业:如:络筒数字式张力仪 DTM200机
针织行业:调节圆织机喂纱张力数字式张力仪 DTM200
光纤行业:如:绕线机
金属线材行业:如:拉丝和绕线机
如果您有特殊张力测量问题而需要定制张力仪表,可以与我们,我们将根据您的特殊应用为您专门设计。
Should you need customized solutions to your measuring problem, please contact us. We will be glad to design a model for your special application.
电池的更换及安装
Battery operated
先拆下电池盖板,装入两节AA电池,同时注意电池的安装方向,然后装上电池盖板。
一,开关机
按住 电源(POWER)键,显示 [ 1500] 启动仪器。
按住 电源(POWER)键,显示 [ - - - - ] 关闭仪器
ON/OFF
Press the POWER key and keep on,,When the instrument’s LCD display [.1000.] , the instrument start up
Press the POWER key and keep on again.The instrument’s LCD display [ - - - - ],the instrument turn off
测量操作过程
开启仪器,确认测量方位后按 调零(ZERO)键,然后活动手柄,使测试材料进入测量头线槽之间。此时显示屏上即显示测量值,活动手柄退出测试材料测量结束。
Operation of test
Turn on the instrument , When you confirm the test positions can press ZERO key . as left map.
保持数据操作
在测量操作过程中,如果需要锁定数据按 保持(HOLD)键,此时仪器进入保持模式;再按 保持(HOLD)键,返回测量模式。
Operation of Hold Data
In Working, You can press HOLD key If you need keep the test data , Now the instrument working in Hold Mode.
Press the HOLD key again , come back to Test Mode
清零操作
开始测量操作之前,张力仪在不同的测量位置,都可以使用 清零(ZERO)键进行清零。
Operation of Zero
Zero Setting using a push button for measure in different positions
电子阻尼操作
在测量操作过程中,当张力值不稳定时,可以通过调节电子阻尼(移动平均数)得到更准确的测试数据。
按 阻尼(DAMP)键可以循环设置十档不同阻尼值。
Operation of Damp
Adjustable electronic damp for better reading when tension is constantly changing
Press the DAMP key ( 10 steps)
力值定标 (注:定标过程中仪器应侧面水平放置在固定平面上)
张力仪力值的定标分为两步1,零位定标:在测量模式下,按住 模式(MODE)键数
秒后仪器进入定标模式,此时显示器显示 [C0.---0] 确认为空载后按 保持(HOLD)键零位定标结束。2,满度定标:零位定标结束后,此时显示器显示 [C1. -100] 确认标准砝码垂直悬挂后再按 保持(HOLD)键满度定标结束,返回测量状态。
Calibrate instrument ( Notice:the instrument must keep level in calibrating )
Instrument can be recalibrated by the operator if required , This process has two steps.
1,In testing mode , Press the MODE key and keeping for 3 seconds , into the Calibrate mode . The instrument’s LCD display [C0.---0] . Confrim the instrument is non load , Press the HOLD key end of zero value calibrate 2, After the zero value calibrate , The instrument’s LCD display [C1. -100] . Confrim the instrument is full load , Press the HOLD key end of full value calibrate , come back to test status.
注意事项:如果没有专门工具或设施,请勿随意定标!
技术参数
Specifications
度 | ±1% FS或者±1数字 | Accuracy: | ±1% full scale and ±1 digit |
单位 | 厘牛(100cN=1N) | Units: | cN |
超量程 | 10%FS,没有精度保证 FS=2000cN | Overrange: | approx. 10% full scale, without accuracy guarantee |
过载保护 | 250% | Overload protection: | 250% of tension range |
测量原理 | 应变电桥 | Measuring principle: | Strain gauge bridge |
测量轮偏移量 | 0.5mm | Measuring roller deflection: | 0.5 mm max. |
信号处理 | 数字式,12位模数转换器 | Signal processing: | Digital, 12 bit A/D converter |
阻尼 | 可调节电子阻尼(10档),移动平均数 | Damping: | Adjustable electronic damp (10steps),moving averaging |
采样速率 | 大约5kHZ(仪器内在频率) | Sampling rate: | approx. 5 khz (internal only) |
显示刷新速率 | 大约4次/秒 | Display update rate: | approximate 4 times /sec |
显示 | 4位液晶显示,12.7mm高 | Display: | 4-digit LCD, 12.7mm high |
温度范围 | 10-45º C | Temperature range: | 10-45º C |
空气湿度 | 大相对湿度85% | Air humidity. | 85% RH, max. |
自动关闭电源 | 不使用3分钟后自动关闭 | Auto power off: | automatically after aprox. 3 min. of non-use |
供应电源 | 2节五号碱性电池(2xAA) 大约能够连续使用50小时 | Power supply: | Two-Cell Allkaline Battery (2xAA) (about 50 hours of continuous use) |
壳体材质 | 铝质框架和外壳 | Housing material: | Aluminum profile with |
手提箱尺寸 | 350x270x80mm(长x宽x高) | Box dimensions: | 350 x 270x 80 mm (LxH) |
重量,净(毛) | 大约500克(1020克) | Weight, net (gross) | approximate 350 g (1020 g) |
Specifications subject to change without notice!