当前位置：深圳市乐买宜电子有限公司>>安全安规测试>>泄漏电流测试仪>>中国台湾华仪 7630 全功能接触电流测试仪 EEC 7630泄漏电流测试仪

中国台湾华仪 7630 全功能接触电流测试仪 EEC 7630泄漏电流测试仪

返回列表页

参考价

面议

具体成交价以合同协议为准

产品型号7630

品牌

厂商性质其他

所在地深圳市

在线询价收藏产品查看联系电话

联系方式：杜全军查看联系方式

更新时间：2024-04-21 14:53:16浏览次数：278次

联系我时，请告知来自智能制造网

产品分类 品牌分类

  安全安规测试

绝缘电阻测试仪

耐压绝缘测试仪

接地电阻测试仪

泄漏电流测试仪

耐压测试仪
  电力电工仪器

万用表、钳形表

电参数测量仪（功率计）

接地表/兆欧表

电阻计、电池测试仪

电能质量分析仪

示波器

功率分析仪
  电源与负载

直流电源

直流电子负载

交流变频电源

交流电子负载
  元器件测试
  行业专用仪器设备

电池行业测试方案
  温升测试与记录
  光学仪器
  热工环保环境监测仪器

温湿度-红外测温仪
  量具量仪

卡尺

暂无信息

深圳市乐买宜电子有限公司

经营模式：其他

商铺产品：408条

所在地区：

联系人：杜全军

询价 给他留言

产品简介

7630泄漏电流测试仪产品介绍具有多项及创新功能，兼具大功率负载量测能力，适合所有接触电流的测试应用；超大型320x240GraphicLCD，可同时显示量测电压/接触电流及测试时间；完整的自动化接口，如网络卡、USBRS-232、IEEE-488(GPIB)及其他接口，可执行自动化测试，亦可搭配华仪安规测试器，组成测试系统，提升测试效率

详细介绍

7630泄漏电流测试仪产品介绍

具有多项及创新功能，兼具大功率负载量测能力，适合所有接触电流的测试应用；超大型 320 x 240 Graphic LCD ，可同时显示量测电压/接触电流及测试时间；完整的自动化接口，如网络卡、USB & RS-232、IEEE-488 (GPIB) 及其他接口，可执行自动化测试，亦可搭配华仪安规测试器，组成测试系统，提升测试效率。

7630泄漏电流测试仪产品特点

量测接触电流时，亦可显示人体仿真阻抗线路(MD)两端的电压，满足接触电流IEC 60990 标准要求
接触电流可量测 AC/DC/AC+DC ，满足医疗设备IEC 60601 标准要求
量测带宽 DC - 1MHz，符合 IEC60990 接触电流测试规范
可灵活选择MD漏电流量测点(如: IEC60065 U1&U2)，符合安规标准要求
内建 7 组人体模拟阻抗(MD)与1组扩充空间，满足多种安规标准要求
可搭配华仪安规测试器组成安规六合一(ACW/DCW/IR/GB/RUN/LLT) 测试系统，缩短测试时间
MD 具有BNC量测端子，可外接示波器或电压表读取电压值，方便对MD进行校准
开机智能检测功能，自动确认仪器输出正常，确保测试的可靠度
校正及预警时间设定功能，提醒用户定期校正，确保测试质量
测试结果可储存过程中漏电流 (Imax)，满足客户对质量的要求
可选配峰值 75mApeak / 有效值 35mArms 量测，满足安规机构测试验证需求

提供7组人体模拟线路（MD）及8组失效模式分析（Fault Condition），模拟真实世界的各种可能触电危险状况。

40A

负载容量可高达40A有效值，使其适用于大电流工业产品。

可同时显示电流测量值或MD两端电压值，清楚呈现测试结果。

7630 Details

Swappable MD

MD可抽换式设计，让使用者易于替换不同选择外，更满足快速的的校验、维修与替换。

支援界面.jpg

Specification :
INPUT
Voltage		115/230 VAC ± 15%
Frequency		50/60 Hz ± 5%
Fuse		2A Slow-Blo 250V AC
Line condition
Power Switch		Reverse polarity switch for normal condition (on / off / auto setting)
Neutral Switch		Neutral switch on/off selection for single fault condition
Ground Switch		Ground switch on/off selection for class I single fault condition
Probe Setting
Surface to Surface (PH- PL)
Surface to Line(PH - L)
Ground to Line (G - L)
Ground to Neutral (G - N)
Auto Function (G - N & G - L)
SETTING
Touch Current High Limit (RMS)	Range:	0.0uA~ 999.9uA/ 1000uA~5999uA/ 6.00mA~20.00mA
	Resolution:	0.1uA/1uA/0.01mA
Touch Current Low Limit (RMS)	Range:	0.0-999.9 uA
	Resolution:	0.1uA
Touch Current High Limit (Peak)	Range:	0.0uA - 999.9uA/ 1000uA - 9999uA/ 10.0mA - 30.0mA
	Resolution:	0.1uA/1uA/0.1mA
Touch Current Low Limit (Peak)	Range:	0.0-999.9 uA
	Resolution:	0.1uA
DISPLAY
Touch Current Display (RMS)	Range 1	0.0uA~ 999.9uA, frequency DC - 1MHz
	Resolution	0.1uA
	Accuracy	DC : ±2% of reading + 3counts 15Hz < f<100KHz : ±2% of reading + 3counts 100KHz < f < 1MHZ : ±5% of reading (10.0uA - 999.9uA)
	Range 2	1000uA~8500uA, frequency DC - 1MHz
	Resolution	1uA
	Accuracy	DC : ±2% of reading + 3counts 15Hz < f<100KHZ : ±2% of reading + 3counts 100KHz < f<1MHZ : ±5% of reading (10uA - 8500uA)
	Range 3	8.00mA~20.00mA, frequency DC - 1MHz
	Resolution	0.01mA
	Accuracy	DC : ±2% of reading + 3counts 15Hz < f < 1MHz : ±5% of reading (0.01mA -20.00mA )
Touch Current Display (Peak)	Range 1	0.0uA~ 999.9uA, frequency DC - 1MHz
	Resolution	0.1uA
	Accuracy	DC : ±2% of reading +2uA 15Hz < f<1MHZ : ±10% of reading +2uA
	Range 2	1000uA ~ 8500uA, frequency DC - 1MHz
	Resolution	1uA
	Accuracy	DC : ±2% of reading +2counts 15Hz < f<1MHz : ±10% of reading +2counts
	Range 3	8.0mA ~ 30.0mA, frequency DC - 100KHz
	Resolution	0.01mA
	Accuracy	DC : ±2% of reading +2counts 15Hz < f < 100KHz : ±10% of reading +2counts
Measuring Device Module
MD1		IEC60990 Fig4 U2, IEC 60950-1, IEC60335-1, IEC60598-1, IEC60065, IEC61010
		IEC60990 Fig4 U1, IEC60065
MD2		IEC60990 Fig5 U3, IEC60598-1
		IEC60990 Fig5 U1
MD3		IEC 60601-1
MD4		UL544NP, UL484 , UL923, UL471, UL867, UL697
MD5		UL544P
MD6		UL1563
MD7		IEC60950, IEC61010-1 FigA.2 (2K ohm) for RUN Test MD Circuit.
External MD		Basic measuring element 1k ohm
MD Voltage Limit		70Vdc
Leakage Current Offset	Range:	0 - 999.9uA
	Resolution:	0.1uA
DUT POWER
AC Voltage		0.0-277.0V
AC Current		40Arms max continuous
Over Current Protection		50Arms, Response Time < 3 sec / 250Apeak Response Time<10u sec
AC Voltage High/Low Limit	Range:	0.0-277.0V
	Resolution:	0.1V/step
AC Voltage Display	Range:	0.0 - 277.0 V
	Resolution:	0.1 volt / step
	Accuracy:	±(1.5% of reading + 2 counts) , 30.0 - 277.0VAC
Delay time setting	Range:	0.2 !V 999.9 seconds
	Resolution:	0.1 second
Timer display	Range:	0.0 !V 999.9 seconds
	Resolution:	0.1 second
	Accuracy:	± (0.1% of reading + 0.05 seconds)
GENERAL
PLC Remote Control		Input - Test, Reset, Interlock & Recall File 1 through10
		Output - Pass, Fail, Test-in-Process, Start-Out, Reset-Out
Scanner Control		It is applied to control Matrix Scanner (Model 7006)
Memory		50 memories , 30steps per each memory . Max. Result Display 900 data (30 memories x 30 steps)
Auto Reverse Function		AUTO Reverse ON / OFF parameter setting selection Automatic Reverse polarity switch for normal condition in one step setting menu. Only display maximum leakage current value.
Scope Output Interface		At rear panel BNC type to connet scope for some IEC standards test requirement and application.
Display		320 X 240 graphic LCD
LCD Contrast Setting		Range: 1-9; 1 is lightest character, 9 is darkest character.
Alarm Volume Setting		Range: 0-9; 0=OFF, 1 is softest volume, 9 is loudest volume.
Security		Lockout capability to avoid unauthorized access to test set-up programs.
Calibration		Software and adjustments are made through front panel, Automatic Calibration alert function to signal operator when calibration is due.
Results Display		All test result information will be displayed on the screen.
Interface		RS232 standard
Safety		Product with TUV/GS certificate
Dimension		430 (W) x 133(H) x 300 (D) mm
Weight		12 Kg
STANDARD ACCESSORIES
Power Cord		X1
Fuses		X2 (Including a spare contained in the fuse holder)
Interlock Disable Key(1505)		X1
TC Receptacle Adaptor Box (1932)		X1
Hipot Test Lead for PH / PL (1101)		X2
RS232 Link Cable 1.5m(1130)		X1
DUT Power Cable 40A(1148)		X1
RUN Module (Opt.752)
W		Range : 0-1KW / 1-10KW Resolution : 0.5W / 5W
A		Range : 0.000 !V 3.500 A / 3.00 - 40.00A , Resolution : 0.001A / 0.01A
PF		0.000 -1.000
Leakage Current		Range : 0.00 - 10.00mA , Resolution : 0.01mA
AC Current High/Low Limit Setting	Range:	0-40A
	Resolution:	0.01A/step
AC Current Display	Range:	0.000 !V 3.500 A / 3.00 - 40.00A
	Resolution:	0.001A / 0.01A
	Accuracy :	± (2 % of reading + 5 counts) / ± (2 % of reading + 2 counts)
AC Power High/Low Limit Setting	Range:	0 - 10KW
	Resolution:	1W
AC Power Display	Range:	0.0 -1000.0W / 1000 - 10000W
	Resolution:	0.5W / 5W
	Accuracy :	±(2 % of reading + 2 counts )
Power Factor High/Low Limit Setting	Range:	0.000 - 1.000
	Resolution:	0.001
Power Factor Display	Range:	0.000 - 1.000
	Resolution:	0.001
	Accuracy :	± (2 % of reading + 2 counts )
Leakage Current High/Low Limit Setting	Range:	0.00 - 10.00mA
	Resolution:	0.01mA
Leakage Current Display	Range:	0.00 - 10.00mA
	Resolution:	0.01mA
	Accuracy :	± (2 % of reading + 2 counts )
Delay Timer Setting	Range:	0, 0.2 - 999.9
	Resolution:	0.1
Dwell Timer Setting	Range:	0, 0.1-999.9 (0=continuous)
	Resolution:	0.1
Timer display	Range:	0.0 - 999.9 seconds
	Resolution:	0.1 second
	Accuracy:	± (0.1% of reading + 0.05 seconds)
Power Control		It is applied to control Transformer Box (1931/1931S) or AC Power Source(6700/6800/6400 Series)
HV & GB Link Module (Opt. 753)
Max. ACW 4000VAC, DCW 4000VDC & Max. Ground Bond 40A
GPIB Interface Card (Opt. 731)
Printer Port Interface Card (Opt. 732)
Multi-function Interface Card (Opt. 751)
Including USB port A type, combination of RS-232, RS-485 port, and Bar Code Input with internal memory capability.
High Measurement Range 35mArms / 70mApeak & 4MDs (Opt. 754 )
35mArms / 70mApeak for IEC60990 fig4(U1 and U2), IEC60990 fig5(U1 and U3), UL484, IEC60601 Test Requiremt , Notice : Option this MD circuit have to replace MD module all MD circuits .
Transformer Box (Option) Add this option must optional Opt.752 RUN Module.
1931 Series Transformer Box (500VA/ 1KVA/1.8KVA/3.6KVA)		Multi-Tape of 1.0, 1.06, 1.1 times of input voltage.
1931-S Series Transformer Box (500VA/ 1KVA/1.8KVA/3.6KVA)		Multi-Tape of 0.8, 0.85, 0.9, 1.0, 1.06, 1.1 times of input voltage.
AC Power Source (Option) Add this option must optional Opt.752 RUN Module.
6800 Series Digital AC Power Source (6805, 6810 , 6820 , 6830 and 6840 )
6700 Series Programmable AC Power Source (6705, 6710 , 6720 , 6730 and 6740 )
6400 Series AC Power Source (6402, 6403, 6405, 6410 )