上海挺扬自控阀门制造有限公司

当前位置:上海挺扬自控阀门制造有限公司>>气动阀门>>气动蝶阀>> QJ(D/S)DX型精小型气动橡胶调节蝶阀

精小型气动橡胶调节蝶阀

参  考  价:面议
具体成交价以合同协议为准

产品型号QJ(D/S)DX型

品牌

厂商性质生产商

所在地上海市

更新时间:2017-09-26 08:59:26浏览次数:1024次

联系我时,请告知来自 智能制造网
QJ(D/S)DX型精小型气动橡胶蝶阀是由气动活塞式执行机构和衬里蝶阀组成,属旋转类控制阀。

一、概述Outline

QJ(D/S)DX型精小型气动橡胶蝶阀是由气动活塞式执行机构和衬里蝶阀组成,属旋转类控制阀。
该产品以压缩空气为动力源,接受控制仪表的4-20mA信号(或开关信号),通过电-气阀门定位器(或电磁阀)实现对阀门的连续调节(或位式控制)。
橡胶衬里蝶阀是一种阀体内腔衬有橡胶的防腐蚀蝶阀。控制腐蚀性流体不与阀体接触,阀体可用普通铸铁或碳钢,由此降低蝶阀的成本。衬里材料有各种橡胶可供选择,还可更换。
该产品结构简单,输出力矩大,性能优越。蝶阀通常适用于控制密封要求比较高的腐蚀性流体。

QJ (D / S) DX-type fine small pneumatic rubber valve is pneumatic piston actuator and lining butterfly valve, is a rotary type control valve.
The product is compressed air as power source, to accept 4-20mA control signal meter (or switch signals, through the electric - gas valve locator (or solenoid valve) to achieve the continuous adjustment of the valve (or bit control.
Rubber lined butterfly valve is a body cavity lined with rubber anti-corrosion butterfly. Corrosion control and body fluid does not contact the valve body can be an ordinary cast iron or steel, thus reducing the cost of butterfly. There are a variety of rubber lining materials available, can be replaced.
The product is simple, the output torque, and superior performance. Control valve normally sealing requirements for high corrosive fluids.

二、主要技术参数Main technical parameters

公称通径mm

50

65

80

100

125

150

200

250

300

350

400

450

500

600

 

额定流量系数Kv

71

100

198

340

500

770

1360

2130

3060

4160

5450

6900

8500

12000

 

公称压力Mpa

0.6、1.0、1.6

 

连接方式

Connection

对夹式(管道法兰标准:JB/T79-94、GB9113-2000 Wafer (pipe flange standard: JB/T79-94, GB9113-2000)

 

介质温度℃ Temperature

 -20~+180

 

输入信号Input signal

0.4~0.6Mpa/调节型0.02-0.1Mpa(4-20mA)

0.4 ~ 0.6Mpa / Regulated 0.02-0.1Mpa (4-20mA)

 

额定行程Rated travel

调节型:70°  切断型:90°

Modulating: 70 ° cut-off: 90 °

 

环境温度℃

Temperature

-40~+150、-40~+180      

 

气源接口

Air Connection

  1/8 ″G 、    NAMUR1/4″G

 

固有流量特性

Inherent flow characteristic

近似等百分比Approximay equal percentage

 

 

泄露等级

Leakage level

 

ANSIB16.104 IV级、VI(软密封)

ANSIB16.104 IV level, VI (soft seal

 

注:允许压差可参照QJD(S)DR型气动蝶阀该指标

Note: Allow pressure to refer QJD (S) DR pneumatic valve of the indicators

三、性能指标Performance indicators

项目Item

带定位器指标值Index value with locator

基本误差Basic error%

 ±2.5

回差Hysteresis%

2.5

死区Dead%

1.0

始终点偏差

Always point deviation%

气开

Open air

始点

Starting point

终点End

±2.5

±2.5

气关

Gas off

始点

Starting point

终点End

±2.5

±2.5

四、执行机构转扭及动作时间Twist and turn actuators operating time


执行机构型号AGT

63×90

75×90

83×90

92×90

110×90

118×90

127×90

160×90

210×90

254×90

255×90

扭矩N.m

400Kpa

23.2

40.0

56.0

77.6

112.8

168.0

220.0

440.0

948.0

1740.0

2172.0

500Kpa

29.0

50.0

70.0

97.0

141.0

210.0

275.0

550.0

1185.0

2715.5

2715.0

动作时间(S)

0.241

0.333

0.429

0.444

0.461

0.60

0.857

1.62

3.33

6.00

7.50

 注:1、双作用执行机构在75%负载情况下的动作时间    2、缩短动作时间可允许非标配置

Note: 1, double-acting actuators at 75% load case, the action time of 2 to shorten the operating time to allow non-standard configuration

五、可配附件Available Accessories

调节型:电-气阀门定位器,空气过滤减压器,手轮机构等。
切断型:定位开关,空气过滤减压器,电磁阀,手轮机构等。

Adjustment type: electric - gas valve positioner, air filter regulator, hand wheel institutions.
Cut-off: position switch, air filter regulator, solenoid valve, hand wheel institutions.

六、主要零件材质与内腔衬材料Material of main parts and cavity lining material

  

零件名称Part Name
 

材料Material

阀体Body

各种橡胶、聚四氟

A variety of rubber, PTFE

蝶板Disc

灰铸铁、球墨铸钢、铸钢、不锈钢及特殊材料

Gray cast iron, ductile cast steel, cast steel, stainless steel and special materials

密封圈Ring

球墨铸钢、铸钢、合金钢、不锈钢

Ductile cast steel, cast steel, alloy steel, stainless steel

阀杆Stem

2Cr13、不锈钢

2Cr13, Stainless Steel

填料Filler

  O型圈、柔性石墨

O-ring, flexible graphite

1.阀体内腔衬材料Body cavity lining materials

材料品种 Variety of materials

氯丁橡胶 Neoprene

丁腈橡胶NBR

乙丙橡胶EPDM

硅橡胶Silicone rubber

氟橡胶Viton

代号Code

X或J

X 或JA

XB或 JB

XD或 JD

XE 或JE

耐zui高温度

Maximum temperature resistance

82℃

93℃

150℃

250℃

204℃

耐zui低温度

Minimum temperature resistance

-40℃

-40℃

-40℃

-70℃

-23℃

适用工作温度

Suitable temperature

≤65℃

≤80℃

≤120℃

≤200℃

≤180℃

七、外形尺寸Dimensions

标准值Standard value
 

参考值Reference

DN

L

D

D1

Z-d

H

H0

A

B

W(kg)

50

43

99

125

4-18

170

130

45

120

24.7

65

46

118

145

4-18

170

145

45

120

25.6

80

46

132

160

4-18/8-18

320

186

160

240

27

100

52

156

180

8-18

320

192

310

100

30.8

125

56

184

210

8-18

345

200

370

118

37.6

150

56

211

240

8-22

385

230

370

118

43.2

200

60

266

295

8-22/12-22

471

297

450

143

100.8

250

68

319

350

12-22

533

327

450

143

118.5

300

78

370

400

12-22

606

364

535

178

159

350

78

429

460

16-22

694

404

535

178

180.7

400

102

480

515

16-26

757

444

630

248

216.8

450

114

530

565

20-26

814

472

1162

232

266.1

500

127

582

620

20-26

902

522

1162

232

325

600

154

682

725

20-30

1048

590

1380

318

355

700

165

794

840

24-30

1277

810

1380

318

585

800

190

901

950

24-33

1385

844

1860

350

798

900

203

1001

1050

28-33

1490

890

1860

350

906

1000

216

1112

1160

28-36

1620

950

1860

350

1055

气动高真空蝶阀

气动高真空蝶阀广泛地应用到冶金、电力、石油、化工、

气动法兰硬密封蝶阀

气动法兰硬密封蝶阀的主要优点,结构简单,体积小重量

气动高真空O型球阀

QJ(D/S)RZ型气动高真空O型球阀是以通过电磁

会员登录

×

请输入账号

请输入密码

=

请输验证码

收藏该商铺

X
该信息已收藏!
标签:
保存成功

(空格分隔,最多3个,单个标签最多10个字符)

常用:

提示

X
您的留言已提交成功!我们将在第一时间回复您~

以上信息由企业自行提供,信息内容的真实性、准确性和合法性由相关企业负责,智能制造网对此不承担任何保证责任。

温馨提示:为规避购买风险,建议您在购买产品前务必确认供应商资质及产品质量。

拨打电话
在线留言