【铜包铝线拉力试验机】厂家

北京北广精仪仪器有限公司是从事专业测量仪器以及相关设备的研发、生产、销售、于一体是股份企业，并按照现代化经营管理实现企业化经营管理模式走向股份制正规

化企业，公司经过长期发展，现已拥有独立的研发队伍并已有海内外专家入注进行产品的研发与设计。

北广公司保持以发展与中国测试产业相适应的应用技术为主线，通过与产业界协调发展的方式提高本公司的竞争实力和技术含量。

公司拥有一支优秀的技术团队，并秉成“创新、精准、高效、跨越”的文化理念逐步打造成为*的仪器检测公司。 同时北广公司强大的售后队伍会对消费者进行全程的

优质服务， 以确保您的*！

中国检测行业与验证服务的*者和智领者，帮助众多检测质检单位和学校教研单位提供一站式的全面质量解决方案。

我公司现有技术人员50人其中 专业研发人员占%15专业技术人员占%25 专业售后人员占%30

北广精仪仪器设备有限公司的经营理念：

   一、诚信待户 顾客至上      全心全意为顾客考虑，使顾客能切身感受到人性化的仪器。

  二、精准检测 保质保量      精准检测是我们的责任 保质保量是我们对客户的郑重承诺

  三、技术 创新理念   储备*的开发人才，引进，采用先进的设计理念，打造zui精良的检测仪器。

北广产品广泛应用于国防、大专院校以及检测所等行业，本公司以技术的创新为企业的发展方向，以新型实用的产品引导客户的需求

北广精仪公司以*的技术、创新的理念、优质的产品获得广大业界的认可，产品在全国范围内广泛销售，获得广大消费者的青睐。

北广公司所供产品严格按照国家标准生产制造，严谨的制造环节确保每一台出厂仪器质量和性能的，服务优质，质优价廉。

        注重每一个细节是北广公司对于每个客户的承诺 ， 也是北广公司一直追求的宗旨。

                          以信誉  营客户     以质量  铸市场    以技术  保精准   以售后 造未来

                                                专业、技术、精准、高跨    

铜包铝线拉力试验机主要技术指标：

01、zui大试验力:单柱结构：0-5KN（试验力大小可根据用户需求而定）

02、试验力显示范围:0～5KN

03、试验力分档：全程不分档-*/

04、试验力测量精度:优于示值的±1% 

05、位移分辨率:0.01mm

06、位移测量准确度:优于示值的±1%

07、横梁移动速度控制范围:0.05mm/min～300mm/min 

08、位移速度控制精度:优于±1%

09、拉伸行程:0～800mm（不含夹具）

10、外形尺寸（长×宽×高）: 435mm×275mm×1700mm（单柱）

11、供电电源:220V、50Hz

Eight, showing the value of deviation is irregular

1, rack, gear oil, abrasion or burr: eliminate the rack, gear oil, burr, find out the pole difference when the contact points, and then modified tooth bar, gear; if not eliminate errors. Replace the tooth bar, gear.

2, tensile testing machine testing machine installation is not level: level adjustment.

3, toothed bar bending: alignment or replacement tooth bar, adjust the roll gap groove wheel.

Nine, computer software on-line prompt box display information overload.

The solution is to check the computer and test machine communication line is off; check the online selection of sensor is correct; check the last test or operation keys

When the sensor is knocked off; check whether the use of a software appears calibration or calibration before; check whether the manual modified calibration values, calibration information value or other hardware parameters in the.

Host ten, the power of the testing machine does not light, not to move up and down.

The solution is power line inspection access testing machine is connected properly; check the emergency stop switch is in screwed up state; power supply voltage check access testing machine is normal; check the socket on the insurance is burned off, remove the spare fuse can be installed.

Host eleven, testing machine power supply with power but the equipment can not move up and down.

The solution is to check whether it is 15S （time） after the device is unable to move, because the host boot take self-inspection, probably need 15S time; check the upper and lower limit is again appropriate position, operating space; check supply voltage access testing machine is normal.

Eight, oil source:

1, regularly check the host and the supply of oil leaks place, if there is oil leakage, should be promptly replaced seal ring or a combined pad;

2, according to the use condition and oil machine use period, replace the oil filter and filter periodically, replacing the hydraulic oil.

Experiment 3, not long time, pay attention to shut off the main power. If the machine is in the standby state, the switch should call the "load" file, because if the switch on the "rewind" file, electromagnetic reversing valve has been in a power-on state, affect the service life of the device.

Nine, control system maintenance:

1, regularly check the controller panel connecting line is good contact, such as loose, should be timely fastening;

2, after the test if there is a long time not machine closed, controller and computer;

3, the controller interface for the corresponding one one, inserted the wrong interface may cause damage to the equipment;

4, Swap Controller Interface must be shut down the power supply controller.