广州市宇亚机电代理ROPEX 热封控制器RES-406

RES -401/ -402/ -403/ -407 For standard applications, mounted on a top hat rail

RES -406/ -409 PROFIBUS/CAN bus interface, mounted on a top hat rail

RES -408 Mounted on a top hat rail, with separate operator terminal

RES -415/ -420/ -440/ -445 Standard devices, front panel mounted

RES -430 For low-cost applications, secondary control

RESCON -470 With programmable functions, front panel mounted

The WA-85-2 is a linear displacement transducer with a total mechanical travel of 8mm. The output voltage changes proportionally to the mechanical travel in the useful range （approx. 4mm）.

The WM-10-x evaluation electronics are optimally tuned to the WA-85-2.

The WM-10-0 evaluation electronics

Evaluate the signal of one
displacement transducer
Allow one switching point to be set

The WM-10-1 evaluation electronics

Evaluate the signal of one
displacement transducer
Allow up to three switching points to be set

The WM-10-2 evaluation electronics

Evaluate the signals of up to three
displacement transducers
Allow one switching point to be set
for each transducer

Analog temperature meter ATR-3/-5

For front panel mounting or mounting on a top hat rail （DIN TS35 rail）.temperature of the heatsealing band in °C. The meter damping of the unit is optimized for the abrupt temperature changes that occur in impulse mode. Analog indication of the ACTUAL

Digital temperature meter DTR-x

For front panel mounting or mounting on a top hat rail
（DIN TS35 rail）.temperature of heatsealing band in °C, with HOLD function. Digital indication of the ACTUAL
 

Set point potentiometer PD-3/-5

Front panel mounting version for setting the required SET heatsealing temperature of the RESISTRON/CIRUS temperarure controller.
The number which appears on the display corresponds
to the SET heatsealing temperature in °C .

Line filter LF-xx480

Essential in order to ensure CE conformity. Optimized for the RESISTRON/CIRUS temperature controllers.
 

Impulse transformer TR-x

Designed according to VDE 0570/EN 61558 with one-section bobin. Optimized for impulse operation with RESISTRON/CIRUS temperature controllers. Dimensioned according to the heatsealing band. （ROPEX Application Report）.

Current transformer PEX-W3

For measurement of the secondary current. Necessary for all RESISTRON/CIRUS temperature controllers.

Monitoring current transformer MSW

For detecting frame short-circuits on the heatsealing band. Used as an alternative to the standard PEX-W2 current transformer.
 

High current bar HCB-1

High current bar, necessary for current measurement with cabel diameter >12mm

Booster B-xxx400

External switching amplifier, necessary for high primary currents （continuous current > 5 A, pulsed current > 25 A）.

Measurement cable UML-1

Twisted measurement cable for UR-voltage measurement. Halogene and silicone free, trailing cable.
 

High current cable C-TC-xx

Special developed high current cable for connecting the sealbars in combination with RESISTRON/CIRUS temperature controllers. Silicone and latex free, trailing cable.

Transparent front cover TFA-x

For increasing the degree of protection on the front of the controller to IP65. Also facilitates applications in the food technology sector （GMP）.

Adapter for top hat rail mounting （HS-Adapter）

For mounting RESISTRON/CIRUS temperature controllers on a top hat rail （DIN TS35）. Allows the controller to be installed in the electrical cabinet, for instance, where it is only accessible to authorized persons.
 

Lockable door TUER-S/K-1

Transparent door （with lock） for mounting on the bezel of the controller. The display is clearly legible at all times. The keyboard can only be operated, however, by authorized persons in possession of a key.

Serial interface RS-232 （MOD 33） --------

Isolated RS-232 interface for the temperature controller RES-420/-440/-445 and UPT/LPT-640. Output of the ACTUAL temperature （with timestamp） during the heatsealing cycle. At the end of the heatsealing cycle the configuration of the controller is transmitted.

Communikation-Interface CI-USB-1 --------

Interface for connecting a RESISTRON/CIRUS temperature controller with diagnostic interface （DIAG） to the PC （USB port）. Associated PC visualization software for displaying setting and configuration data, and for recording SET and ACTUAL temperatures in real time.