当前位置：深圳市恒胜泰科技有限公司>>磁性器件>>蜂鸣器>>5020贴片SMD无源蜂鸣器5V 3V 体积5*5*3

5020贴片SMD无源蜂鸣器5V 3V 体积553

返回列表页

参考价

面议

具体成交价以合同协议为准

产品型号MLT-5020

品牌

厂商性质经销商

所在地深圳市

在线询价收藏产品查看联系电话

联系方式：王生查看联系方式

更新时间：2018-01-17 17:12:29浏览次数：1214次

联系我时，请告知来自智能制造网

产品分类 品牌分类

  磁性器件

蜂鸣器
  二三极管

三极管

暂无信息

深圳市恒胜泰科技有限公司

经营模式：经销商

商铺产品：3条

所在地区：广东深圳市

联系人：王生（销售）

询价 给他留言

产品简介

频率：4000HZ
电压：3V/5V
电阻：12/16欧姆
驱动方式：压电式（晶体式）
种类：蜂鸣器（片）
品牌：CHINA
加工定制：是
是否有源：有源/无源

如需详细请：：王货源：

详细介绍

B. SPECIFICATION

No.	Item	Unit	Specification	Condition
1	Oscillation Frequency	Hz	4000	Vo-p=1/2duty , square wave
2	Operating Voltage	Vo-p	2 ~ 4
3	Rated Voltage	Vo-p	3
4	Current Consumption	mA	MAX.110	at Rated Voltage
5	Sound Pressure Level	dB	MIN. 75	at 10cm at Rated Voltage
6	Coil Resistance	Ω	12±3
7	Operating Temperature	℃	-30 ~ +70
8	Storage Temperature	℃	-40 ~ +85
9	Dimension	mm	5.0 x 5.0 x H3.0	See appearance drawing
10	Weight (MAX)	gram	0.6
11	Housing Material		LCP( Black )
12	Leading Pin		Tin Plated Brass(Sn)	See appearance drawing
13	Environmental Protection Regulation		RoHS

C. APPEARANCE DRAWING
undefined

Tol : ± 0.3 Unit: mm

D.TESTING METHOD
Standard Measurement conditions
Temperature:25±2℃ Humidity:45-65%

Acoustic Characteristics:
The oscillation frequency, current consumption and sound pressure are measured by the measuring instruments shown below

In the measuring test, buzzer is placed as follows:

undefined

E. Typical Frequency Response Curve

undefined

F. Recommend Driving Circuit

undefined

The base current Ib should high enough so that it saturates the collector current of the transistor with the CB load.

G. Soldering Condition
(1)Recommendable reflow soldering condition is as follows
(Reflow soldering is twice)
Note:It is requested that reflow soldering should be executed after heat of product goes down to normal.

Heat resistant line

undefined

(Used when heat resistant reliability test is performed)
(2)Manual soldering
Manual soldering temperature 350 ℃ within 5 sec.

H. RELIABILITY TEST

NO.	ITEM	TEST CONDITION AND REQUIREMENT
1	High Temperature Test (Storage)	After being placed in a chamber with 852℃ for 96 hours and then being placed in normal condition for 2 hours. Allowable variation of SPL after test: 10dB.
2	Low Temperature Test (Storage)	After being Placed in a chamber with -402℃ for 96 hours and then being placed in normal condition for 2 hours. Allowable variation of SPL after test: 10dB.
3	Humidity Test	After being Placed in a chamber with 90-95% R.H. at 402℃ for 96 hours and then being placed in normal condition for 2 hours. Allowable variation of SPL after test: 10dB.
4	Temperature Cycle Test	The part shall be subjected to 5 cycles. One cycle shall be consist of: Allowable variation of SPL after test: 10dB.
5	Drop Test	Drop on a hard wood board of 4cm thick, any directions ,6 times, at the height of 75cm . Allowable variation of SPL after test: 10dB.
6	Vibration Test	After being applied vibration of amplitude of 1.5mm with 10 to 55 Hz band of vibration frequency to each of 3 perpendicular directions for 2 hours . Allowable variation of SPL after test: 10dB.
7	Solderability Test	Lead terminals are immersed in rosin for 5 seconds and then immersed in solder bath of +3005℃ for 31 seconds . 90% min. lead terminals shall be wet with solder (Except the edge of terminals).
8	Terminal Strength Pulling Test	The force of 9.8N(1.0kg) is applied to each terminal in axial direction for 10 seconds. No visible damage and cutting off.

TEST CONDITION.
Standard Test Condition : a) Temperature : +5 ~ +35℃ b) Humidity : 45-85% c) Pressure : 860-1060mbar
Judgment Test Condition : a) Temperature : +25 ± 2℃ b) Humidity : 60-70% c) Pressure : 860-1060mbar

I. PACKING STANDARD

undefined

如需详细请：：王货源：