3nh 或 DNP标准灯箱 3nh & DNP Standard Color Viewer (CC5100可以替代 SDCV3500)
产地：OEM 或 日本
技术参数
DNP标准颜色Viewer
是摄影机及静相摄影机的评价，调整用的光源装置。
能看由于高频荧光灯点灯方式的采用闪烁不定没有的画像。
DNP灯管大量现货供应！FL10D-EDL-56K >>>
方法:
光源: DNP标准颜色viewer油灯
(特殊荧光管10W×4个使用)
电源: AC100v50，60Hz
点灯方式: 高频点灯方式20KHz
演颜色性: 对各颜色演颜色评价点90以上
色温: (美能达制CL-200测量)
使用温度: 10～40〓C
使用湿度: 80％以下(结露没有事)
外形尺寸: 375W×365H×165D m/m
亮度方面尺寸: 250W×190H m/m
海图尺寸: 320W×290H m/m
消耗功率: 80W
重量: 6.5kg/7.5kg
由于viewer包藏荧光油灯的差异的亮度方面的特性
对待说明
【1】 使用前
电源:AC电源100v，50Hz，60Hz共用
光源:DNP标准颜色viewer油灯 10W×4个
消耗功率:80W
【2】 使用
(1) AC100v的插座插入电源编码的插头。
※注意: AC100v以外的电源请别连接。
在海外利用时候，必定拜托您了变压器的使用。
变成弄错AC100v以外的电源连接的话被安上内部取的变压器的烧毁。
(2) ON电源开关。
(3) 以油灯点灯常温(20℃)点灯后15～20分稳定。
(4) 油灯不点灯的时候，向别的项目的大街电保安人员要求请求确认。
(5) 油灯的胫―王现象发生了的时候修好做电源开关3～4次ON，OFF。
【3】 油灯不点灯的时候
请在电保安人员确认。
(1) 插座AC100v通上电流。
(2) 插座插入viewer的插头。
(3) viewer的电源开关ON。
Viewer的油灯不点灯的时候，能考虑象下面一样的事
(1) 油灯2盏点灯的时候，变压器的一方的保险丝溶断做着。
(2) 油灯4盏是不点灯的时候，2台变压器的各々的保险丝溶断做着。
※注意: 上述(1)(2)AC100v以外的通电的时候发生。这变压器内部烧毁是原因。
变压器的交换变成必要。
【4】 与油灯的交换清扫
在平的台里(上)放置viewer从插座上请取下电源编码。
以下面的顺序进行卸载。
(1) 放松上面框框的硬币螺钉2处。
(2) 用双手举起50～60毫米上面框框的硬币螺钉方面推到前方的话上面框框偏离实体。
(3) 取下玻璃板和丙烯板。
※注意: 玻璃板因为有破裂请当心手手指。
(特别象用手手指不擦一样地请注意板边方面。)
■油灯交换
(1) 又，1年流逝的时候点灯2,000小时。
(2) 脱离用双手手指夹油灯的管端部使之转90〓。
■清扫工作
(1) 请在纱布中浸湿酒精擦去反射板表面，丙烯板和玻璃表面的污秽取。
(2) 清扫为了6个月～1年1次，正常保持色温，亮度无论如何拜托您了。
【5】 使用前
viewer因为使用着玻璃品请注意下面的事。
(1) 请别给(对)viewer实体给予大的冲击。
(2) 请别搁置对viewer表面沉重的东西。
| DNP Standard color Viewer |  |
|
|
|
| The DNP Standard color Viewer is a light source which enables you to evaluateadjust videostill cameras. With its high-frequency Fluorescent lighting method, it handles images without flicker. |
Specification
| Light source: | DNP Standard color Viewer lamp
(Four 10W dedicated fluorescent tubes are used) |
| Power supply: | AC100V 50, 60Hz |
| Lighting method: | High Frequency lighting method 20KHz |
| Color rendering: | Over 90% rendering evaluation-point for each color |
| Color temperature: | (Measured by Minolta CL-200) |
| Operating temperature: | 10～40℃ |
| Operating humidity: | Below 80%(avoid dew) |
| Major diameter dimension: | 375W×365H×165D m/m |
| Luminance plane dimension: | 250W×190H m/m |
| Color chart dimension: | 320W×290H m/m |
| Power consumption: | 80W |
| Weight: | 6.5kg/7.5kg |
| ●The Luminance plane characteristics: according to the types of self-contained fluorescent lamp |
|
| Product Type | Luminance Color Temperature | Lamp | Color Temperature | Luminance | Color matching shift | Weight | | CCV-31F | Fixed | FL10WW-DLB | 3100K±300 | Over 1300cd/m2 | Within 10% | 6.5kg | | CCV-51F | Fixed | FL10D-EDL-56K | 5100K±300 | Over 1400cd/m2 | Within 10% | 6.5kg | | CCV-31F/G | Volume adjustable | FL-10WW-DLB | 3100K±300 | Over 850～1300cd/m2 | Within 10% | 7.5kg | | CCV-51F/G | Volume adjustable | FL10D-EDL-56K | 5100K±300 | Over 850～1400cd/m2 | Within 10% | 7.5kg |
|
|
＊The color temperature if Luminance. Color Temperature Conversion Type viewer ranges over 50k according to the change of the Luminance.
＊The specification may change without notice |
|
|
|
| 【1】 | Before using the product: | | | | Power supply | | AC 100V, 50/60Hz shared | | Light source | | 10W DNP Standard color Viewer Lamp (4) | | Power consumption | | 80W |
|
|
| 【2】 | Using the DNP Standard color Viewer | | | | (1) | Plug the power cable of the product into AC100V | | | | | 【Precautions】 | Do not connect any power supply other than AC100V
If the other power supply connected by accident, the inverter inside will burned out |
| | | (2) | Turn on the power switch | | | (3) | Lamp lights: the lamp light will stabilised after 15 to 20 minutes at the room temperature(20℃) | | | (4) | If the lamp does not lit, call for Service Office for the confirmation as described on other documents. | | | (5) | To suspend snaking of the lamp, press power switch 3 to 4 times [as ON/OFF]. |
|
|
| 【3】 | If the light does not lit | | | | Call for Service Office to confirm the following: | | | (1) | AC 100V supplied to the wall socket. | | | (2) | Plug the product into the wall socket. | | | (3) | Turn the power supply switch of the product ON | | | | |  | | | | Still the lamp does not lit: Consider the following: | | | | | | | | | (1) | Two of the viewer lamps lit simultaneously, one of the fuses of the inverters has blowouts. | | | (2) | Four of the viewer lamps does not light means that each of the fuses of the two inverters has blowouts. | | | | | 【Precautions】 | The above occurs if the applied power supply is not AC 100V.
Fuse bum out cause internal burnout of inverter. The burned inverter needs to replace. |
|
|
|
| 【4】 | How to replace the lampkeep it clean | | | | Place the Viewer on the flat table,plug out the power supply cable from the wall socket.
Remove the used device in the following order: | | | (1) | Unfasten the two of grub screws on the top frame. | | | (2) | To remove the top frame from the main unit;
Holding 50 to 60 mm the grub screw of the top framepress it forward. | | | (3) | Remove the glass plateacrylic plate. | | | | | 【Precaution】 | Glass plate easily breaksmay hurt your handsfingers.
Handle the edge of the plate with care not to scratch. |
| | | | ◆Replacing the lamps: | | | (1) | When the lamps used over 2,000 hours or one year, it needs to replace. | | | (2) | Remove the Lamp Tubes: Hold the edge of the Lamp Tubes,turn it 90 degree. | | | | ◆Cleaning the device: | | | (1) | Impregnate alcohol to gauze then apply it onto the surface of the reflection plate / acrylic plate / glass surface to remove the dirt. | | | (2) | Clean the device once in six months to one year to keep quality of the Color TemperatureLuminance. |
|
|
| 【5】 | Other Precautions | | | | Handling the viewer needs the following precautions because it contains the parts using glass. | | | (1) | Do not add strong impact on the viewer | | | (2) | Do not put any heavy items on the surface of the viewer |
|
智能制造网