产品参数: 外形尺寸:355mm×95mm×236mm 重 量:2.63千克 以太网速率:10/100Mbps 网络连接:10/100BaseT,MT-RJ光纤接口 无线通讯:802.11a、802.11b 安 全 性:IEEE 802.1x、WEP64、WEP128 工作温度(带加热器):-30℃-70℃ 存储温度:-30℃-75℃ 操作温度:10-90%GH(工业标准 产品优势 同时支持802.11a 和802.11b双无线频段的AP。 拓展了企业的通讯带宽,装备有更强大的处理器,内存和出色的、 基于802.1x标准的新型安全技术。 它采用了全金属的坚强结构,密封性能达到IP54。 可在-30℃-70℃的范围内正常工作。 并可通过以太网来供电。 同时采用了Intermec的双无线电模块技术和WEP128保密机制。 的IP Tunneling技术充分保障了企业级的无缝漫游。 LAN Access – WA21 / WA22 The WA21/WA22 has been designed with the future in mind. They have a larger processor and more memory when compared to the older 2100/2101 platform of products. The processor comes into play when dual radios are in operation, or when the Embedded Access Server (EAS) or future access point functionality is in use. Feature | WA21 /WA22 | 2100D / 2101B | Processor | 250MHz | 80MHz | Flash | 4MB | 4MB | Ram | 16MB | 8MB |
The WA21/WA22 has other improvements that are not available in the 2100/2101 series of access points as listed below: WA21 – comes POE enabled, can be ordered with POE and AC power - This is an either or option on the 2100D • WA21/WA22 – POE compatible with LAN™power (PowerDsine) and Cisco and 802.3af – The 2100/2101 are only compatible with LAN™power. • • • • • WA22 POE – only powered via POE, however the one port power bridge, 071620 can be used the same way that an AC power supply is used. WA22 – comes with robust TNC Antenna connectors – not available on the 2101B WA21/22 - has a Plenum rating – not available on the 2100D/2101B WA21/22 – faster radio support, 802.11a, 802.11g (when available) – the 2100/2101 products cannot support these and future radios.
Access Point 2.4GHz Antennas Click here to access the Intermec Antenna Guide Model | Part Number | Description | Comments | Photo | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 063363 | Antenna, 2.4GHz 5dBi Isotropic, 3dBd | FCC ETSI Can be used in Europe for Open Air, DS, or High Rate Open Air - min 20' antenna cable, 802.11 Hardware for mast installation provided | | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 063365 | Antenna, 2.4 Ghz, 15dBi Yagi | FCC Available for 802.11 DS/HR only This antenna is designed to have the base attached to a wall. Hardware for mast installation is also provided Gain 15 DBI Azimuth Plane 34° Elevation/Vertical Plane 30° The patterns shown assume the base of the antenna is mounted to a wall. The six o’clock point is the base of the antenna. | | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 063366 | Antenna, 2.4Ghz 14dBi Flat Panel | FCC Hardware for mast installation provided Gain 14 DBI Azimuth Plane 30° Elevation/Vertical Plane 30° | | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 065349 | Antenna, 2.4GHz 9dBi Omni | FCC ETSI Can use in Europe for Open Air, DS, or High Rate Open Air - Antenna must be used with minimum 40' antenna cable or a 20' minimum antenna cable and splitter DS or High Rate, must be used with minimum 20' antenna cable Hardware for mast installation provided Gain 9 DBI Azimuth Plane 360° Elevation/Vertical Plane 14° | | 2100D 2102B WA21A WA21B WA22A WA22B | 066147 | Antenna, 2.4GHz Omni | FCC ETSI Gain 1 DBI Azimuth Plane 360° Elevation/Vertical Plane 90° | | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 067261 | Antenna, 2.4GHz 3dBi Mini Omni | N Receptacle Connector FCC ETSI Can use in Europe for Open Air, DS, or High Rate. Open Air - Antenna must be used with minimum 10' antenna cable DS or High Rate - approved for use The back surface can be mounted to a wall or ceiling. hardware for drop-ceiling installation is also provided Gain 3 DBI Azimuth Plane see below Elevation/Vertical Plane see below | | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 067262 | Antenna, 2.4GHz, 5dBi Duel Flat | FCC This antenna should be installed so that the large flat sides face the down the corridor Gain 5 DBI Azimuth Plane 60° Elevation/Vertical Plane 30° The patterns shown assume the antenna is mounted as described above. The six o’clock and twelve o’clock points are the two large surfaces. | | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 067263 | Antenna, 2.4GHz 9dBi Flat Panel | FCC This antenna is mounted with the back surface to a wall. The side of the antenna where the cable exits is normally pointed to the ceiling. Also provided with Velcro patches, plastic drywall anchors, self threading screws and Tilt Pan bracket. Gain 9DBI Azimuth Plane 60° Elevation/Vertical Plane 60° The patterns shown assume the antenna is mounted as described above. The six o’clock point is the portion of the antenna (back) that is mounted to the wall. | | 2101B | 069753 | Antenna, 2.4 GHz, Omni, 2101 (spare) | FCC ETSI No cable, Adapter required Approved for use in Europe-Open Air Gain 1DBI Azimuth Plane 360° Elevation/Vertical Plane 90° | | 2101B | 069903 | Antenna, 2.4GHz, Omni, 2102/802.11b (spare) | FCC ETSI No cable, Adapter required Approved for use in Europe -DS or High Rate Gain 1DBI Azimuth Plane 360° Elevation/Vertical Plane 90° | | 2101B 2102B | 070140 | Antenna, 2.4GHz, 3dBi Mini Flat-Open Air | FCC ETSI MMCX Connector Can use in Europe for Open Air. Open Air -Antenna must be used with minimum 10' antenna cable The back surface can be mounted to a wall or ceiling. hardware for drop-ceiling installation is also provided Gain 3 DBI Azimuth Plane see below Elevation/Vertical Plane see below | | 2101B 2102B | 070141 | Antenna, 2.4GHz, 3dBi Mini Flat - 802.11b | FCC ETSI Radiall (Lucent) Connector Can use in Europe. for DS or High Rate The back surface can be mounted to a wall or ceiling. hardware for drop-ceiling installation is also provided Gain 3 DBI Azimuth Plane see below Elevation/Vertical Plane see below | | WA21A WA21B WA22A WA22B | 071121 | Antenna, 2.4GHz, Diversity, 3dBi | FCC Provided with integral clip for drop-ceiling installation Gain 3DBI | | WA21A WA21B WA22A WA22B | 071122 | Antenna, 2.4GHz, Corner Reflect | FCC Hardware for mast installation provided Gain 9DBI Azimuth Plane 65° Elevation/Vertical Plane 75° | | 2101B 2102B | 071488 | Antenna, 2.4 GHz, Diversity Ant, | MMCX Connector Proxim Mounts to ceiling, wall, or desk. Hardware for drop-ceiling installation provided Gain 2DBI Azimuth Plane 360° Elevation/Vertical Plane 50° | | 2101B 2102B | 071489 | Antenna, 2.4GHz Diversity Ant, | Radiall Connector 802.11B, Lan card 11 Mounts to ceiling, wall, or desk. Hardware for drop-ceiling installation provided Gain 0DBI Azimuth Plane 60° Elevation/Vertical Plane 60° | WA21A WA21B WA22A WA22B | 072730 | Antenna, 5.25-5.35GHz, Omni, Swivel TNC, 4dBi | FCC- Mid Band Gain 4DBI Azimuth Plane 360° Elevation/Vertical Plane 35° | | WA21A WA21B , , WA22A WA22B | 072759, FONT> | Antenna, 5.25-5.35GHz, Omni, 6dBi | FCC- Mid Band Hardware for mast installation provided Gain 6DBI Azimuth Plane 360° Elevation/Vertical Plane 25° | | WA21A WA21B WA22A WA22B | 072760 | Antenna, 5.25-5.35GHz, Omni, 9dBi | FCC- Mid Band Hardware for mast installation provided Gain 9DBI Azimuth Plane 360° Elevation/Vertical Plane 14° | | WA21A WA21B WA22A WA22B | 072761 | Antenna, 5.25-5.35GHz, Omni, 3dBi, Ceiling Mount | FCC - Mid Band Mounting Kit includes screws and wall anchors Gain 3DBI Basic Pattern Hemispherical Omni-Directional | | WA21A WA21B WA22A WA22B | 072762 | Antenna, 5.25-5.35Ghz, Corner Reflect | FCC - Mid Band Hardware for mast installation provided Gain 14DBI Azimuth Plane 30° Elevation/Vertical Plane 60° | | WA21A WA21B | 073304 | Antenna, Diversity, OMNI, 3dBi, TNC | | | WA21A WA21B | 073373 | Antenna, 2.4ghz, 3dBi, mini-omni, TNC | | | WA21A WA21B | 073374 | Antenna, 2.4ghz, 5dbi, dual flat panel, TNC | | | WA21A WA21B WA22A WA22B | 073375 | Antenna, 5ghz, 3dbi, omni, ceiling mount TNC | | | WA21A WA21B | 073984 | Antenna, 2.4ghz, 14dBi, Corner Reflector | | |
Access Point 2.4GHz Antenna Cables & Connectors Click here to access the Intermec Antenna Guide Model | Part Number | Description | Comments | Photo click to view larger image | 2100D 2101B 2102B | 061868 | Lightning Suppressor and Bracket | | | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 063198 | Splitter, 2.4 GHz only | | | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 063245 | Cable, 60" (152cm) | N-plug to N-Plug Extension Cable Plenum rated cable equivalent - #072825 | | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 063246 | Cable, 20' (610 cm) | N-plug to N-Plug Extension Cable Plenum rated cable equivalent - #072826 | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 064616 | Cable, 30" (76 cm) | N-plug to N-Plug Extension Cable Plenum rated cable equivalent - #072824 | WA21A WA21B WA22A WA22B | 065090 | Cabel assy, TNC Plug/N Recept, Cisco | Cisco | | 2100D 2101B 2102B ITDEL WA21A WA21B WA22A WA22B | 067265 | Cable TNC Plug/N Recept, 12 in LMR200 | Plenum rated cable equivalent - #072821 | | 2100D 2101B 2102B PF4CI PF2iA WA21A WA21B WA22A WA22B | 067266 | Cable Adapter, 2100 AP to antenna | TNC to N-Plug cable connection 24" LMR200 To Antenna - Plenum rated cable equivilent - #072821 | | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 071178 | Cable, LMR400, TNC/N Male, 12 Ft (366 cm) | Plenum rated cable equivalent - # 072823 | | WA21A WA21B | 077179 | Cable, N Plug/N Plug, LMR600, 30' | Plenum rated cable equivalent - #072827 | | WA21A WA21B | 072821 | Cable, TNC Plug/N Rec, 12" Plenum | | | WA21A WA21B | 072822 | Cable, TNC Plug/N Plug, 24", Plenum | | | WA21A WA21B | 072823 | Cable, TNC Plug/N Plug 12', Plenum | | | WA21A WA21B | 072824 | Cable, N Plug/N Plug, 30" Plenum | | | WA21A WA21B | 072825 | Cable, N Plug/N Plug, 5' Plenum | | | WA21A WA21B | 072826 | Cable, N Plug/N Plug, 20' Plenum | | | WA21A WA21B | 072827 | Cable, N Plug/N Plug, 30' Plenum | | | WA21A WA21B WA22A WA22B | 073446 | Cable Assy, TNC Plug/N Plug, 6ft | | | WA21A WA21B WA22A WA22B | 073447 | Cable Assy, TNC, Plug/N Plug 6ft, PLRT | | | WA21A WA21B WA22A WA22B | 073517 | Cable Assy, TNC plug/N recept, 15 inc | | | WA21A WA21B WA22A WA22B | 073518 | Lightning Suppressor 2.4 to 5.9 Ghz | | | 2.4 GHz Antenna, Cables (Variable length, made by user) | Model | Part Number | Description | Comments | Photo | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 061475 | Connector, N Plug Antenna Cable | Variable length made by user | | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 063146 | Connector, N Receptacle Antenna Cable | Variable length made by user | | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 063153 | Kit, Shrink Tubing 1", black, 6 ea x 4" | Variable length made by user | | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 064432 | Cable, LMR400-100' | N-Plug Cable Variable length made by user | | 2100D 2101B 2102B WA21A WA21B WA22A WA22B | 589377 | Prep Tool, LMR400 Cable | Variable length made by user | | 2.4 GHz Antenna Adapters | Model | Part Number | Description | Comments | Photo | 2101B 2102B | 069886 | Adapter Cable, 2101/2102 MMCX | to N-receptacle cable connection Used to connect 2101 and 2102 pc card radio with MMCX connector to Intermec N Plug | | 2101B 2102B | 069887 | Adapter Cable, 2101/2102 802.11b | to N-receptacle cable connection Used to connect 2101 and 2102 pc card radio with Radiall (Lucent) connector to Intermec N Plug. | | 2101B 2102B | 069910 | Adapter Cable, 2101/2102 MMCX/TNC | To Cable Adapter 067265 or 067266 | | 2101B 2102B | 069911 | Adapter Cable, 2101/2102 802.11b | To Cable Adapter 067265 or 067266 | | 2101B 2102B | 070402 | Adapter Cable, 2101/2102, MMCX/N-Plug | Adapter for N-Plug cables Used to connect 2101 and 2102 pc card radio with MMCX connector to Intermec Antennas 063363, 063365, 067261, 067262, 067263, 071121, and 071122 | | 2101B 2102B | 070403 | Adapter Cable, 2101/2102 802.11b/N-Plug | Adapter for N-Plug cables Used to connect 2101 and 2102 pc card radio with Radiall (Lucent) connector to Intermec Antennas, 063363, 063365, 067261, 067262, 067263, 071121, and 071122 | |
Access Point Insulation Kits & Mounting Brackets Click here to access the Intermec Antenna Guide Model | Part Number | Description | | Photo click to view larger image | 2100D WA21A | 068216 | Kit, Insulation, 2100 AP for -20C to -30C cold temp only | | | 2100D WA21A | 068751 | Kit, Mounting Bracket Rotation, 21xx | | | 2100D WA21A | 068918 | Mounting Bracket | | | 2101B 2102B | 069888 | Bracket, Mounting, Antenna, Dual | | | 2101B 2102B 2106A | 069893 | Kit, Power Supply Holder | | | 2101B WA22A | 069926 | Kit, Cubical Mount | | | 2101B | 070184 | Kit, 2101, Locking Bracket | | | 2101B 2102B 2106A WA22A | 070222 | Kit, Mounting Bracket, 2101 (spare) | | | 2102B 2106A | 070366 | Kit, Cubical Mount | | | | 1-010560-01 | Mounting Kit for Wireless Printing The kit will fit any EasyCoder 3240, 3400, 3440, 3600, 4420, 4440, F2, F4, 501 XP or 601XP, equipped with EasyCoder 10i or 100i, Internal Ethernet Card. | | |
Access Point Radio Kits Be sure to verify RF compliance before ordering. Model | Part Number | Description | Comments | Photo click to view larger image | 2100D | R2100A491 | Kit, Radio, 900 MHz Falcon - FCC | 2.4GHz kits also available in options 503 or 703 - ETIS Radio upgrade kits should be installed by trained personnel only. Price does not include installation or antenna. Installation of radios into the 2100 access point must support only the radio mix options supported by the 2100 UAP. Country codes MUST be the same in two radio installations. Radio options supported are (Radio slot 1/Radio slot 2) 900 Falcon/Empty, 2.4GHZ Open Air/Empty | | 2100D | R2100A504 | Kit, Radio, 2.4 GHz OpenAir -FCC | | 2100D | R2100A704 | Kit, Radio, IEEE 802.11b w/WEP, FCC | | 2101B | R2101A704 | Radio Kit, IEEE802.11b w/WEP, FCC | This kit also available with option 703 - ETSI | | WA21A WA21B WA22A WA22B | RWA2XA704 | Kit, Radio, Upgrade, 704, WA21A, FCC | Radio upgrade kits should be installed by trained personnel only. Price does not include installation or antenna. Installation of radios into the WA21A access point must support only the radio mix options supported by the WA21A Country codes MUST be the same in two radio installations. Radio options supported are 802.11a and/or 802.11b radios only | | WA21A WA21B WA22A WA22B | RWA2XA703 | Kit, Radio, Upgrade, 704, WA21A, ETSI | | WA21A WA21B WA22A WA22B | RWA2XA708 | Kit, Radio, Upgrade, 704, WA21A, Mexico | | WA21A WA21B WA22A WA22B | RWA2XA904 | Kit, Radio Upgrade, 904, Low/Mid band, int ant (IEEE 802.11a radio, operates 5.15-5.35 GHz, factory integrated antennas | | WA21A WA21B WA22A WA22B | RWA2XA954 | Kit, Radio Upgrade, 954, Mid band, remote ant (IEEE 802.11a radio, operates 5.15-5.35 GHz, supports remote antennas | |
|
|